Questions tagged [usb-host]
A USB host port implements the upstream end of a USB connection
222
questions
0
votes
0
answers
19
views
USB Type-C DFP Host Port implementation without Switch
I am currently designing a new board that has a four port USB 3.2 x1 Gen1 hub on it. I only need two ports and now thinkering how to best make use of the other two ports.
The idea was to make at least ...
1
vote
4
answers
96
views
Why USB-C plug doesn’t charge? [closed]
I have multiple USB-C 5V chargers of the same type that do not charge connected android devices. Devices detect charging if these are turned off, but when turned on, no charging icon of any visual ...
0
votes
0
answers
49
views
How should I select the ohm values for pull-up and pull-down resistors in a device with a USB Type-C connector used solely for power
Good morning, everyone. I am exploring the transition of the receptacle from a micro USB connector to a USB Type-C. Initially, my plan included implementing both sink and source capacity. However, ...
1
vote
1
answer
155
views
Replace micro USB tablet connector with USB C
I'm considering upgrading my dad's old tablet, which currently has a micro USB connector. The issue arises from his habit of frequently misplacing the charger, and I'd prefer not to rely on an ...
0
votes
0
answers
40
views
Converting a USB HID K/M Composite Device to a USB HID Compound Device (or Two Seperate K/M Devices)
I want to connect a USB composite device (Raritan KX4-101) with keyboard and mouse descriptors to a USB matrix switch with a very picky HID keyboard and mouse emulation (Extron SMX USB).
From what I ...
0
votes
2
answers
41
views
USB 3.0 SS lines issue
Can you route USB 3.0 SS lines to two PCB's but the USB controller is located on the second PCB?
The PC host is connected to the first PCB over a usb c-c connection (center usb port in image). Then ...
1
vote
1
answer
93
views
Is it possible to apply quick charge 3.0 to USB-C?
There's a wall outlet with a USB-A fast charging port
It has a USB-A charging port that supports 9V 1.67A fast charging.
It uses FP6601Q and supports QC2.0/QC3.0.
I'm trying to change the USB-A ...
0
votes
0
answers
73
views
USB-c R1/R2 configuration
I have a usb-c cable that plugs into a 4s lithium ion battery (DJI FPV goggle battery with proprietary cable.) The battery will only turn on if the usb-c plug (picture below) is plugged into it. I ...
1
vote
2
answers
77
views
USB Current Oscillation ~ 100 mA Without Device [closed]
Apologies for my lack of deep knowledge here - this is not my background and I am definitely an amateur so I greatly appreciate your willingness to help me!
Background: I was curious about the ...
0
votes
0
answers
52
views
USB peripheral not responding to SETUP packets
I'm writing some Verilog on a Spartan S7-50 FPGA to control a MAX3421E (datasheet) over SPI. I've gotten everything working with setting up the chip (full-duplex, Vbus, connection detection, host mode)...
0
votes
0
answers
47
views
UART over USB for radio transciever board
I am creating a telemetry radio that operates over UART, but I want to interface via a USB port so the same connection can be used between the flight computer and the onboard radio and between the ...
0
votes
1
answer
256
views
USB HUB for OTG
I have designed a custom board with Processor which is having a dedicated USB 2.0 OTG port. I want to convert it to 4 USB OTG ports. so I was thinking to use the USB 2.0 HUB with OTG support for 4 ...
-1
votes
1
answer
348
views
USB host, STM32. f_mount returns FR_DISK_ERR
I'm trying to connect a USB flash drive to an STM32F407VGT6.
IDE Keil,
I used compilers 6.19 and 5.06.
...
0
votes
2
answers
78
views
What is the communication protocol used by non-expansion card USB ports to communicate with CPU?
USB ports can come as expansion cards, like this:
Now obviously, since this is a PCIe USB card, the communication protocol used by this expansion card to communicate with CPU is PCIe.
But what about ...
1
vote
1
answer
91
views
Computer interface with USB devices
I'm making a computer peripheral that will be connected via a USB.
The main brain is an STM32 ARM MCU, it has USB support natively.
It has multiple sub-peripherals inside and it uses I2C and SPI to ...