Questions tagged [operational-amplifier]
Questions relating to the construction and applications of operational amplifiers, which are DC-coupled, high-gain electronic voltage amplifiers with a differential input and, usually, a single-ended output.
8,514
questions
0
votes
2
answers
30
views
Strange asymmetric saturation with ADA4099
Good afternoon — my first question here, I hope I follow all the rules...
So, I am trying to design a series of filters with op-amps that have a shutdown pin, using only 0 → 3.3V supply and an analog ...
-2
votes
0
answers
60
views
Audio amplifier for a physics experiment, how do I make it? [closed]
The experiment includes a mic taking in sound(2KHz-4KHz) and sending it to a DSO. I need an audio amplifier circuit in between that to amplify the signal so it would be visible properly. The ...
0
votes
2
answers
72
views
What type of amplifier circuit do I need to drive a piezoelectric ultrasound transducer?
I would like to drive the following piezoelectric transducers at 200 V or their maximum voltage (60-1000 V):
https://www.manorshi.com/16mm-Dog-Repellent-Ultrasonic-Transducer-25khz-Detect-Sensor-...
2
votes
2
answers
82
views
TL072CP non inverting circuit doesn't amplify
I am using TL072CP op amp in inverting mode to amplify guitar signal.
This is the circuit I have made:
I assembled it and even when changing resistors of different values and trying out different ...
1
vote
2
answers
58
views
How to simulate for the Gain of opamp Bridge Differential Amplifier?
Hi experts,
I have this circuit, with a bridge connected to an op-amp in differential form, and I want to simulate it for the Gain of the circuit in PSPICE.
I have found it's gain by hand, which comes ...
0
votes
1
answer
44
views
Audio Codec Input/Output Channel Stages
I am planning to build a PCB for a Eurorack Modular Synthesizer, incorporating an STM32 for DSP and a bidirectional Audio Codec like the TLV320AIC3104 to handle the ADC/DAC.
Eurorack audio signals ...
5
votes
7
answers
919
views
Infinite output impedance in amplifier, instead of 0?
The question asks: "Exercise 14.5 Assume an ideal op amp and use the summing-point constraint to find an expression for the output current io in the circuit of Figure 14.14. Also find the input ...
0
votes
0
answers
59
views
Applying KVL in op amp with floating source
From my understanding, the solution first applies the summing point constraint even though there is no ground on the non-inverting input, leading to 0V on both inputs. But how do they apply KVL across ...
6
votes
4
answers
320
views
Is it correct to apply KVL through the 2 inputs of an op amp?
The question asks; "P14.25 Analyze each of the ideal-op-amp circuits shown in Figure P14.25 to find expressions for 𝑖𝑜. The top part is the question, the bottom is the solution from the ...
3
votes
2
answers
212
views
+200
How are opamp node voltages being set in the following circuit and what is the use of the diode configuration?
I am using a PCB which has the following opamp configuration implemented. It's supposed to be a precision buffer for the source V3. I accidentally connected the source V4 as well and observed strange ...
4
votes
3
answers
487
views
Issues with ICL7660 ICs from eBay - Overheating and Failure
I recently purchased several cheap ICL7660 ICs from eBay to use in an OpAmp circuit. Unfortunately, I've encountered issues with these components, specifically overheating and subsequent failure.
Here ...
0
votes
2
answers
86
views
What is the maximum dBu I can send into a microphone input in this schematic?
The schematic below is from the Icom 9700 radio service manual (page 80). I would like to feed this input from a mixer board's ALT-3/4 outputs, and I want to avoid blowing the TS462 microphone preamp ...
0
votes
1
answer
64
views
Part name of this IC - "LLA#537"
I want to know the part numbers of the components marked as shown in the attached image.
4
votes
1
answer
188
views
Part name of this IC - Analog Devices, 8-pin, "S 6B" A 06" "C 42"
I want to know the part numbers of the components marked as shown in the attached image.
1
vote
0
answers
52
views
Need help analyzing sability of op-amp in a current source in LTSpice
I have to perform stability analysis on an op-amp (AD8671) which is being used as an op-amp in the circuit attached. I am using LTSpice to perform this. My approach is to give a 1V AC small signal at ...