Questions tagged [adc]
An ADC is an Analog to Digital Converter. This device converts analog signals into digital form. It is mainly used by digital circuitry to take analog measurements.
3,115
questions
0
votes
4
answers
94
views
What does it mean the MCU has 1 ADC and 10 ADC channels?
I got this AVR Microchip MCU ATtiny 204 chip. Now what I can't get, what do they mean in the datasheet it has 1 ADC and 10 channels ADC?
The datasheet:https://datasheet.octopart.com/ATTINY204-SSF-...
0
votes
2
answers
33
views
Switching ON/OFF an ADC line
which electronic component could one use to switch ON/OFF several external lines for ADC?
Context:
I am working on a small project where I would like to measure 4 external voltages (0-3V range, let's ...
- 101
-1
votes
0
answers
37
views
ICs for Low Voltage Analog to Digital Conversion [closed]
I'm looking for an ADC IC that works in very low voltage ranges (0 - 50mV), and with a resolution of at least 1024 steps. I was wondering if anyone knew if this sort of device even existed, or what a ...
0
votes
1
answer
37
views
How to use ADC to measure chained battery?
I have developed an ADC board using AD7192 to measure battery voltage. Assume each battery is 3V, the chained battery in series would gives 15V in total. Let the battery be BAT1+, BAT1-, BAT2+, BAT2- ....
- 21
2
votes
1
answer
42
views
ADC DNL INL Confusion
The DNL of an ADC is defined as the measured code width versus the ideal LSB code width.
The INL is the integral of the DNL (or the running sum of it).
But the INL has two methods - end point and best ...
- 3,145
0
votes
1
answer
90
views
STM32G4x 2 chanel Contunious Conversion Mode ADC DMA voltage read problem
I am using STM32G431KB Nucleo for measure a potentiometer voltage via ADC1_IN1 and ADC1_IN2 channels with Scan Mode DMA. And my samples arrays are always zero, no change. I share my code below. What ...
- 27
1
vote
0
answers
20
views
Not correct reading in ADCs DACs integrated system
I made a ADCs board (AD7194) and DACs board (AD5689). Each DAC (separated ground) could output 0-5V, and Each ADC channel could measure 0-3.3V. I used a voltage divider network to turn 0-5V to 0-3.3V. ...
- 11
0
votes
1
answer
64
views
Part name of this IC - "LLA#537"
I want to know the part numbers of the components marked as shown in the attached image.
- 71
4
votes
1
answer
188
views
Part name of this IC - Analog Devices, 8-pin, "S 6B" A 06" "C 42"
I want to know the part numbers of the components marked as shown in the attached image.
- 71
0
votes
0
answers
41
views
Simplest JFET front end to A/D converter
This is regarding a cheap Pmod I2S2 ADC and DAC (connected to an STM32F407G-DISC1) that uses a Cirrus CS5343 ADC.
Now, as best as I can tell from the CS5343 data sheet, the \$ V_{PP} \$ of the input ...
- 1,705
5
votes
2
answers
167
views
How do I create a circuit to reliably calculate a range of unknown resistances?
I'm designing a low power circuit which serves to determine the unknown resistance across a 16 channel sensor. So far the results are bit subpar. The resistances are a function of a different applied ...
- 113
2
votes
1
answer
79
views
Is this extra cycle before the MSB a common thing with serial bit timing?
The products that this is specifically around are the Pmod I2S2 which uses the Cirrus CS5343 ADC and CS4344 DAC. It is plugged into a STM32F407G-DISC1.
Now I am having some trouble figuring out ...
- 1,705
1
vote
0
answers
15
views
How to understand and compare ADC errors between LTC2314-14 and internal ADC of STM32F103
We are going to sample and curve a short, fast-changing signal of around 34 us, with a reasonable resolution of at least 10 bits.
A 4 Msps ADC would provide us around ~138 data points in 34 us
The ...
- 2,017
2
votes
2
answers
53
views
Wiring of INA128 instrumentation amplifier to Wheatstone bridge
Is there any issue with the wiring or calculations of my INA128 instrumentation amplifier to my load cell Wheatstone bridge? Currently I see no change in the output when connected to the oscilloscope. ...
- 21
0
votes
0
answers
34
views
Noise Figure at the Rx ADC output
I need to measure gain & nf of the Rx at the ADC output. I inject sine wave tone to the Rx input. Then I make a ram dump of the IF ADC output, read it, perform fft and finally get the IF PSD.
My ...
