Abstract
Maintaining food safety and quality is critical for public health and food security. Conventional food preservation methods, such as pasteurization and dehydration, often change the overall organoleptic quality of the food products. Herein, we demonstrate a method that affects only a thin surface layer of the food, using beef as a model. In this method, Joule heating is generated by applying high electric power to a carbon substrate in <1 s, which causes a transient increase of the substrate temperature to > ~2000 K. The beef surface in direct contact with the heating substrate is subjected to ultra-high temperature flash heating, leading to the formation of a microbe-inactivated, dehydrated layer of ~100 µm in thickness. Aerobic mesophilic bacteria, Enterobacteriaceae, yeast and mold on the treated samples are inactivated to a level below the detection limit and remained low during room temperature storage of 5 days. Meanwhile, the product quality, including visual appearance, texture, and nutrient level of the beef, remains mostly unchanged. In contrast, microorganisms grow rapidly on the untreated control samples, along with a rapid deterioration of the meat quality. This method might serve as a promising preservation technology for securing food safety and quality.
Similar content being viewed by others
Introduction
Meat is an important source of proteins, fatty acids, vitamins, as well as minerals such as iron and zinc, making it an important food source for human beings1,2,3. Global meat consumption has been growing steadily for several decades, exceeding 300 million tons since 20184. However, meat is also prone to spoilage, due predominantly to the rich nutrient composition providing an excellent growth media for microorganisms, including food-born human pathogens and spoilage microorganisms. Thus, meat needs to be properly preserved and stored to ensure safe consumption.
Meat preservation is typically achieved by storing at low temperatures (4 °C within 4 h of slaughtering), or by freezing (<−20 °C) or super-chilling in a partially frozen state. In general, low-temperature methods have the advantage of maintaining better meat freshness compared to other techniques such as drying, smoking, and canning, or through chemical preservation (using salts, nitrites, acids, etc.), or biopreservation (using natural antimicrobial agents such as essential oils, nisin, and lysozyme, etc.)5,6. However, safely transporting meat requires energy to maintain the cold chain storage, which over long distance can be subject to disruption, risking spoilage and contamination with harmful microorganisms.
In this work, we demonstrate an ultra-high-temperature flash heating (UFH) method that can efficiently preserve meats while retaining their nutrient level and texture. The concept stems from a similar ultra-fast and high-temperature heating method, also known as flash Joule heating, that has been previously applied in materials science to sinter ceramics7, synthesize high entropy catalysts8, recycle plastics9, and convert waste (including food waste)10, etc. Here, we propose to adapt this technology to food preservation. In this approach, Joule heating is achieved by applying a high electric power (~1800 W) over a short time interval (<1 s) to a carbon substrate, creating a transient increase of the substrate temperature to >~2000 K. By placing the meat in direct contact with the carbon substrate, this rapid heating causes ultra-fast dehydration and inactivation of microorganisms on the meat surface, forming a thin (~100 μm) protective layer that also serves as a barrier to inhibit inward bacterial migration toward the bulk of the meat. As a result of surface dehydration and microorganism-inactivation after the application of UFH, we achieved an extended shelf life of 5 days at room temperature for beef storage without compromising the interior appearance, texture, and nutrition of the meat. The UFH method is essentially a food surface treatment technology, which could be cost-effective for the industrial-scale preservation of large carcasses. The approach could be used alone or in combination with low-temperature technologies to decrease the risk of temperature variation during transport and storage for improved food safety.
Results
UFH creates a microbe-inactivated and dehydrated thin layer on the meat surface
A conceptual illustration of the UFH for the surface treatment of meat is shown in Fig. 1. The carbon felt is connected to a DC power supply (not shown), and is heated to >~2000 K in less than 1 s. For demonstration purposes, a beef steak (Fig. 1a) is placed on the carbon felt; the beef surface is subjected to ultra-fast dehydration and inactivation of microorganisms during the current pulse and associated high-temperature flash heating. The entire UFH process recorded by a high-speed camera (200 fps) can be seen in Supplementary Movie S1. Figure 1b compares UFH with other heating methods, in terms of temperature and operating time11,12,13,14,15,16,17. In general, the temperature in the UFH is an order of magnitude higher than that in conventional food heating methods, such as boiling, baking, and grilling; and it is more than 3–4 orders of magnitude faster. A butane torch may reach a temperature that is close to the UFH, but the heat transfer is mainly through convection, which is still 2 orders of magnitude slower. The effect of the UFH is schematically shown in Fig. 1c–e using a 1 cm3 beef cube. The heating procedure is applied to all six faces of the cube. Compared to the fresh beef (Fig. 1c), the UFH-treated beef possesses a thin, dehydrated outer layer that seals the surface (Fig. 1d, e); allowing the bulk beef to remain fresh (Fig. 1e).
As a proof-of-the-concept experiment, we placed a 1 cm3 beef cube (prepared from sirloin beef stored at ~253 K before use) between two pieces of carbon felt, which served as the Joule heating element (Fig. 2a). When a transient current passed through the carbon felts, their temperature increased due to the Joule heating effect, causing the emission of electromagnetic radiation (Fig. 2b). The brightness of the carbon felt is associated with its temperature, which can be determined using a high-speed camera and color ratio pyrometry (Fig. S1)18. Fig. 2c shows a typical heating profile change for the carbon felt during the UFH process, where a temperature of ~1500 K at ~0.2 s and a peak temperature of 2091 K at ~0.7 s was observed. The period during which the carbon felt temperature exceeds 2000 K lasts for ~0.2 s.
We conducted a two-dimensional numerical simulation to investigate the transient temperature distribution of the beef sample during the UFH process. To simplify the simulation, we assumed that only one face of the beef was in direct contact with the carbon felt heating element, with the other faces being exposed to an air environment at 293 K. The initial bulk temperature was set at 253 K, which is typical for long-term food storage19. The simulation results indicate that the beef surface temperature increased from ~450 K at 0.1 s to the peak point of ~900 K in 1 s during the UFH, then quickly dropped down below ~400 K in 5 s, after the heating was stopped (Fig. 2d). Our simulation also showed that at distances of >~2 mm from the heated surface, the beef temperature was almost unchanged.
The overall appearance of fresh and the UFH-treated beef, as well as the cross-section of the UFH-treated beef, are shown in Fig. 2f–h. Image analysis (see Fig. S2 in the Supplementary Information for details) of the histological micrograph (Fig. 2i) reveals the thickness of the surface layer is ~100 μm. The dark appearance of the UFH-treated beef may be due to surface carbonization. Scanning electron microscopy (SEM) reveals the meat featured a rough surface after heating (Fig. 2j). Additionally, electron dispersion spectroscopy (EDS) analysis indicates that the dark regions consist mostly of carbon (Fig. 2k). Raman spectra reveal that the surface of the UFH-treated beef shows two enhanced peaks at 1374 and 1596 cm−1 as compared with the central region of the meat sample (Fig. 2l). We assign these two broad peaks to the D- and G-band of graphite, indicating the existence of carbon species in a poorly ordered form20,21.
Microbiological tests reveal a significant inhibition in the growth of microorganisms during storage, due to the UFH treatment
Meat appearance can be used as a quick check of the microorganism proliferation (Fig. 3a). The UFH-treated and untreated beef were stored at room temperature for 80 h, and their central regions were examined every 20 h. The visual appearance of the UFH-treated beef remained largely unchanged during storage under these conditions (top row in Fig. 3a). Meanwhile, the color of untreated beef became dark in the first 20 h and the surface appeared watery after 40 h due to microbial proliferation (bottom row in Fig. 3a).
To quantify the efficacy of the UFH method for inhibiting bacterial and fungal growth, we compared the content of microorganisms including total aerobic mesophiles (represented in aerobic plate count (APC)), enterobacteriaceae (EB), and yeasts and molds (YM), for the UFH-treated and untreated beef samples at room temperature (Fig. 3b–f). Microbiological tests were performed on a short-term (24 h) and long-term (100 h) basis; and the Baranyi–Roberts model was used to fit the microbial growth profile (solid lines in Fig. 3d–f)22. For the untreated beef, APC and EB counts increase rapidly in the first 24 h while the APC counts remain below the detection limit in the first 22 h and EB 24 h for the UFH-treated beef (the lower detection limit of APC and EB are 0.70 and 0.48 log CFU/g, see Methods section for details), as shown in Fig. 3b, c. Long-term tests reveal the complete microbial growth profiles for untreated beef (Fig. 3d–f for APC, EB, and YM, respectively). Note that data of short-term test for YM is not shown, as the YM count remains undetectable for both untreated and UFH-treated beef; but long-term test clearly shows a rapid increase in YM populations in the untreated beef after 20 h and reaching ~106/g (Fig. 3f) after 100 h. In contrast, no YM were detected in the UFH-treated beef during the entire 100 h period. At the late stages of storage, the untreated beef samples had completely spoiled, whereas the bacterial counts in the UFH-treated beef samples barely reached the critical limits23. For example, according to the USDA Agricultural Marketing Service (AMS), the APC critical limit for ground beef is 4.0 log CFU/g24. The APC counts of untreated beef stored at room temperature exceeds the critical limit after ~12 h (Fig. 3b), while that of the UFH-treated beef remain below the limit even after storing for 100 h. We also conducted the cytotoxicity assessment of the surface of the UFH-treated beef to address potential safety concerns. Compared to untreated beef, the cell viabilities of 3T3-L1 (mouse embryonic fibroblast cell) and CCD18co (human colon tissue cell) did not change when cultured with the addition of beef sample collected from the UFH-treated surface (Fig. 3g).
UFH treatment maintains beef quality during storage
Besides assuring safety, it is critical for a preservation method to maintain food quality as characterized by appearance, texture, and nutrient level. Texture is an important measure for meat quality, being directly associated with the mouthfeel during consumption25. We conducted rheological experiments including a strain sweep of the storage modulus \({G}^{{\prime} }\) (elastic behavior) and the loss modulus \(G\hbox{''}\) (viscous behavior) to assess how the UFH treatment might affect the texture of the beef samples. Rheological data of untreated and UFH-treated beef after 100 h of storage at room temperature is shown in Fig. 4a (rheological data was collected every 20 h during the storage, see Fig. S8). The untreated samples show \({G}^{{\prime} }\) and \(G\hbox{''}\) values that are ~4 times lower than the UFH-treated samples. Food texture can be generally categorized into four classes: tough, rubbery, mushy, and brittle as quantified by stress and strain values at the end of the linear viscoelastic region in a stress-strain curve26,27. Fresh as well as UFH-treated beef behave as a “tough” material (Fig. 4b). During storage, the texture of the untreated samples experienced a change from “tough” to “mushy” due to myofibrillar protein decomposition caused by microbial spoilage. The texture change of the UFH-treated beef is much more localized in the stress-strain plot (Fig. 4b). A slight shift towards the “brittle” region is due to moisture loss during storage at room temperature. These results show the UFH treatment has a negligible effect on the texture of the beef samples, which we attribute to the fact the process affects only the surface of the meat.
We also studied the difference between untreated and UFH-treated beef in terms of their freshness and nutritional value. The color of meat is a direct indicator of its freshness. We use the Euclidean distances of the RGB components of the color at randomly picked pixels on a meat photograph to characterize the appearance of the beef samples28. Using fresh carcass as a reference, the central region of the UFH-treated beef maintains at the same level of the Euclidean distance over 80 h, while the untreated beef group shows a significant increase in the Euclidean distance, which is also evidenced by the dark hue of the beef sample. This is due to various oxidation processes when meat is exposed to air and light29,30,31, as well as the meat spoilage during storage (Fig. 4c)6,30.
Proteolytic activities of the microorganisms break down the proteins in meat, creating peptides and amino acids that are further decomposed into low-grade amines and ammonia32. These deterioration processes raise the risk of food poisoning and may significantly lower the nutrient level. Three chemical markers, i.e., the non-protein nitrogen (NPN) content (Fig. 4d)33,34, pH value (Fig. 4e)35,36, and total volatile basic nitrogen (TVB-N) content (Fig. 4f)37,38,39, were used to assess the freshness and nutrient level. All three markers remained essentially unchanged during storage for the UFH-treated beef. However, for the untreated beef, the NPN content increased from ~24 mg/g to ~31 mg/g by the late phase of storage at 80 h (Fig. 4d). Additionally, the pH value increased from 5.6 (±0.02) to 7.2 (±0.3) (Fig. 4f); and the TVB-N content increased by ~10-fold (Fig. 4f). These results strongly suggest that the UFH-treated beef can remain fresh for a time frame of approximately 100 h.
Discussion
We attribute the marked inhibition of microbial growth after UFH treatment of the beef to the combined effects of surface dehydration and microorganism inactivation. The meat surface temperature reaches ~900 K due to the carbon felt temperatures of ~2000 K during the UFH treatment (Fig. 2d). More importantly, UFH causes water evaporation, leading to a dehydrated layer of ~1 mm in thickness (Fig. 2e), which is consistent with the surface water activity (\({a}_{w}\)) measurements: \({a}_{w}\) at surface maintains at ~0.8 during storage for 80 h, while the untreated beef shows a much higher water activity of ~0.99 (Fig. S5). \({a}_{w}\) is one of the major parameters that limits food microbial growth. Most bacteria and many yeasts proliferate when \({a}_{w}\) > 0.91 while the growth of most molds requires \({a}_{w}\) > 0.8040,41. Maintaining a value of \({a}_{w}\) of ~0.8 at the beef surface plays a critical role in inhibiting microbial growth. These findings suggest that the UFH results in similar microbial growth inhibition mechanisms as conventional drying and dry-curing42, but the latter methods significantly modify the overall meat texture and flavor.
It needs to be pointed out that thermal radiation is the dominating heat transfer mechanism in the UFH method, as evidenced from the high light emission of the heating element (Fig. 2b). As a result, the UFH treatment does not require perfect contact between the meat surface and the heating element, which allows it to sterilize the material even when the meat surface is rough. Additionally, the UFH method can be scaled up since the heating element is flexible and can effectively cover expansive areas with irregular surfaces, such as large carcasses, with imperfect contact being overcome by the radiative heat transfer.
Our objective of food processing is to preserve the freshness of food products, maintaining their native properties to as high a degree as possible without introducing chemical additives and/or prolonged processing time. The UFH method is a food surface treatment, producing a protective thin layer (sterilized and dehydrated) that helps delay various oxidation processes that may alter meat color and texture. Conventional heating methods, due to prolonged heating time (Fig. 1b), may significantly denature proteins. For example, beef myosin, actin, and collagen denature between 54–58 °C, 71–83 °C, and 65–67 °C, respectively43,44. As seen in Fig. 2d, temperature variation only takes place on the meat exterior (~2 mm from the surface); and the interior temperature remains unchanged throughout the process. When heating is ceased, the inward heat transfer from the meat surface relies solely on thermal conductance, and the heat is quickly dissipated to the environment via convection (Fig. S10). In this regard, the UFH meat surface treatment is fundamentally different from conventional cooking, in which the entire piece of meat is cooked. Note that at this stage the UFH serves as an auxiliary meat preservation method since frozen meat was used as a model; however, no significant obstacles are foreseen to its application to fresh meats.
Understandably, concerns about potential health risks due to the extremely high-temperature treatment of the meat may arise. Therefore, we conducted a cytotoxicity assessment that indicated the UFH-treated surface does not show cell toxicity, since surface carbonization might be the dominant chemical process, as revealed by Raman spectroscopy (Fig. 2l). Additionally, the generation of acrylamide, a carcinogenic compound to humans, is one of the major health concerns of cooking methods such as grilling and frying. High-performance liquid chromatography-mass spectrometry (HPLC-MS) analysis indicates that the acrylamide concentration remains at a level of <7 parts per billion (ppb) in the UFH-treated beef surface (Fig. S3), which is far less than the 500-ppb benchmark limit set by the European Union regulation45. Furthermore, HPLC full scan analysis indicates that heterocyclic aromatic amines (HAA) and benzo(a)pyrene are absent from the samples (Tables S1 and S2).
The ‘charred’ appearance of the UFH-treated meat may impact the acceptance by customers. Therefore, the UFH method may be most useful for large-scale meat treatment (e.g., handling carcasses at slaughterhouses) since the cost-effectiveness is inversely proportional to the specific surface of the bulk meat. After preservation and transport, the ‘charred’ surface layer (~100 μm in thickness) can be removed from the bulk meat at the retailer’s end to ensure that the product is appealing to consumers. Future research may be conducted to avoid the carbonization effect by lowering the heating temperature and still maintaining the formation of the dehydrated surface layer.
Economic gain beyond reduced energy usage due to lowered refrigeration needs may be achieved, owing to the room temperature microbial inhibition effect of the UFH. An increase in the storage temperature of food can be caused by unpredictable factors such as power outages or equipment malfunctions46. An extension of shelf life at room temperature may significantly mitigate the risk of food spoilage due to temporary unplanned temperature increases. A full life cycle analysis, however, is not available, because it depends heavily on multiple factors, such as the application targets (though in principle this method is most energy efficient for large meat pieces such as carcasses, smaller products such as primal or subprimal cuts of meat are other options) and meat distribution scheme, etc. The heating device needs to be optimized to satisfy various application needs.
Methods
UFH experiment
Carbon felt of 4 \(\times\) 2.5 cm was used as the heating element (AvCarb G280A, FUELCELL Store). The two ends of a carbon felt were attached to graphite plates using copper clamps connected to a DC power source (MP10050D, StarPower). The output current and voltage of the DC power source were adjustable between 0–50 A and 0–100 V, respectively. The heating cycle time can be controlled. In a typical UFH experiment output power of ~1800 W was applied to a carbon felt in <1 s, corresponding to a temperature profile maintaining a peak temperature of ~2100 K for ~0.2 s (Fig. 2c). Two carbon felts can be used together to simultaneously heat the top and bottom surfaces of an object.
The temperature evolution of the carbon felt was measured using a high-speed camera (Vision Research Phantom Miro M110) based on color ratio pyrometry, with videos recorded at 200 frames/s18.
The beef was purchased from a local retailer. To facilitate cutting and shaping, the beef was briefly stored in a freezer and then taken out and cut into cubes of 1 cm3. The beef cubes were then separated into two groups (used for the UFH treatment and control), each contained in a Ziplock bag, and were stored at −253 K until the UFH experiments.
Thermal and water content analysis during UFH
We use COMSOL MultiPhysics software, based on the finite element method, to study heat transfer and the change in the water content of frozen beef during the UHF process. Our model, illustrated in Fig. S10, is reduced to a two-dimensional problem, where only the surface of the frozen beef is heated, while the remaining parts are exposed to ambient conditions. The heating element is positioned at the bottom of the frozen beef, generating a high temperature of 2000 K for a duration of 1 s. This heat transfer increases the beef temperature, melts the ice, and causes water within the beef to evaporate. The simulation is performed in a time frame of 10 s, including both the heating and the cooling phases. Details such as heat transfer equations, basic assumptions, boundary conditions, as well as material property parameters used in simulation are given in the Supplementary Information.
Microbiological tests
The UFH-treated and control samples, 5 g each, were collected, immersed in 45 mL of sterile buffered peptone water (BPW), and stomached for 2 min using a stomacher (Seward type 80, UK). Additional four dilutions of 10−1, 10−2, 10−3, 10−4, and 10−5 were successively prepared. For the long-term test, five additional dilutions of 10−3, 10−6, 10−9, 10−12, and 10−15 were prepared.
Aerobic Plate Count (APC). All dilutions were evenly dispensed onto the APC plate (Petrifilm™, 3M). The prepared plates were incubated at 35 ± 1 °C for 48 h, and the colony number was then counted. The countable range was between 25 and 250 CFU.
Enterobacteriaceae (EB). All dilutions were plated following the same procedure for APC, using (Petrifilm™, 3M). The EB count plates were incubated at 35 ± 1 °C for 24 h, and the colony number was then counted. Red colonies associated with gas bubbles or colonies surrounded by yellow zones with or without gas were counted. The countable range was between 15 and 100 CFU.
Yeast and Mold (YM). All dilutions were plated following the same procedure for APC, using rapid yeast and mold count plate (Petrifilm™, 3M). The EB count plates were incubated at 25 ± 1 °C for 48 h, and the colony number was then counted. All red colonies were counted regardless of their size or color intensity. The countable range was between 10 and 100 CFU.
Chemical characterization
Total protein content. A nitrogen determinator (Leco TruMac N) was used to quantify the total protein content in beef samples. 1.0 ± 0.2 g of beef sample was loaded into a ceramic boat and was dried at 101 ± 1 °C for 45 min in a convection oven before the nitrogen analysis measurements. Blank boat weight was measured with a standard deviation of <0.002%. Ethylenediaminetetraacetic acid (EDTA) was used as a calibration standard. The furnace temperature was 1100 °C, with a lance flow of ≈1.8 L/min and purge flow of ≈4.2 L/min. A nitrogen-to-protein conversion factor of 6.25 was multiplied to report the protein content based on the measured nitrogen content.
Total volatile basic nitrogen (TVB-N). The Conway method was used to determine TVB-N. 10 g of minced beef, with 100 mL of DI water added, was homogenized for 30 min (Ultra-Turrax T25, IKA, Staufen, Germany).
Into the inner chamber of a Conway dish with a diameter, 3 mL of boric acid absorption solution (20 g/L) and 50 mL of pH indicator (mixture of methyl red and bromocresol green at 1:5 volume ratio) were added; and into the outer chamber 3 mL of potassium carbonate saturated solution and 1 mL of filtered liquid beef homogenate were added, successively.
The Conway dish was then sealed and incubated for 2 h at 37 °C. HCl (0.1 mol/L) was used to titrate against the boric acid-absorbed nitrogenous compounds. The TVB-N content \({c}_{{TVBN}}\)(mg/100 g) was quantified by
where \({v}_{1}\) is the HCl titration volume for the tested sample (mL), and \({v}_{2}\) of the blank sample (mL); \(c\) is the actual concentration of HCl (mol/L); \(m\) is the weight of the beef sample (g).
Cytotoxicity assessment
3T3-L1 and CCD18co cell lines were obtained from the American Type Culture Collection (ATCC, CL-173). Cells were seeded and cultured in the Dulbecco’s modified Eagle’s medium, containing sodium bicarbonate (3.7 g/L), penicillin-streptomycin (1%), and bovine calf serum (10%). Adipocytes were developed after treating the post-confluent cells with fetal bovine serum (10%), 3-isobutyl-1-methylxanthine (0.5 mM), dexamethasone (1.0 mM), and insulin (1.67 mM) after two days.
Physical characterization
Scanning electron microscopy (SEM). Beef samples were freeze-dried before the SEM (Tescan XEIA FEG SEM, Brno, Czechia) experiments. The sample surface was coated with a platinum layer of 1 nm thick; and the SEM measurements were performed under 10 kV accelerating voltage. A 4pi Analysis System was used to acquire the images (Durham, NC).
Raman spectroscopy. Freeze-dried beef samples were used for the experiments, using a Horiba Jobin Yvon (Edison, NJ) confocal Raman spectrometer. The excitation laser wavelength was 532 nm and the objective lens magnification was 10×. Spectra were collected using a 600 g/mm grating. Neutral density filters were added to prevent sample damage if needed.
Texture analysis. A strain sweep was performed on the beef samples with a thickness of 2 mm at room temperature, using a rheometer in parallel plate geometry (TA Instruments). Plateau stress and strain at the end of the linear viscoelastic region were used to quantify the beef texture.
Histological microscopy. Beef samples were soaked in phosphate buffer (pH = 7.4) containing 4% (volume fraction) of formaldehyde first, and were then plunged into liquid nitrogen-cooled isopentane. A cryomicrotome (Leica Microsystems 3050S, Nussloch, Germany) was used for sectioning. Histological studies were performed using an optical microscope (Olympus VS-BX), and micrographs were registered by a digital camera (VC50).
Color analysis. Euclidian distances \({D}_{E}\) were computed based on 50 randomly picked pixels on a photograph of beef, using the following equation:
where \(R\), \(G\), and \(B\) represent the three components, red, green, and blue, of the color at a given pixel. The subscripts (2 and 1) refer to two different pixels28.
Data availability
Source data are provided with this paper.
References
Trumbo, P., Schlicker, S., Yates, A. A. & Poos, M. Dietary reference intakes for energy, carbohydrate, fiber, fat, fatty acids, cholesterol, protein and amino acids. J. Am. Diet. Assoc. 102, 1621–1630 (2002).
Mann, J. & Truswell, A. S. Essentials of Human Nutrition (Oxford Univ. Press, 2017).
Whitney, E. & Rolfes, S. R. Understanding Nutrition (Cengage Learning, 2018).
Parlasca, M. C. & Qaim, M. Meat consumption and sustainability. Annu. Rev. Resour. Econ. 14, 17–41 (2022).
Zhou, G. H., Xu, X. L. & Liu, Y. Preservation technologies for fresh meat – a review. Meat Sci. 86, 119–128 (2010).
Dave, D. & Ghaly, A. E. Meat spoilage mechanisms and preservation techniques: a critical review. Am. J. Agric. Biol. Sci. 6, 486–510 (2011).
Wang, C. et al. A general method to synthesize and sinter bulk ceramics in seconds. Science 368, 521–526 (2020).
Yao, Y. et al. Carbothermal shock synthesis of high-entropy-alloy nanoparticles. Science 359, 1489–1494 (2018).
Dong, Q. et al. Depolymerization of plastics by means of electrified spatiotemporal heating. Nature 616, 488–494 (2023).
Luong, D. X. et al. Gram-scale bottom-up flash graphene synthesis. Nature 577, 647–651 (2020).
Dryer, F. L. Water addition to practical combustion systems—concepts and applications. Symp. Int. Combust. 16, 279–295 (1977).
Mehta, R. S. Milk processed at ultra-high-temperatures – a review. J. Food Prot. 43, 212–225 (1980).
Morgan, A. I., Radewonuk, E. R. & Scullen, O. J. Ultra high temperature, ultra short time surface pasteurization of meat. J. Food Sci. 61, 1216–1218 (1996).
García-Segovia, P., Andrés-Bello, A. & Martínez-Monzó, J. Effect of cooking method on mechanical properties, color and structure of beef muscle (M. pectoralis). J. Food Eng. 80, 813–821 (2007).
Mondal, A. & Datta, A. K. Bread baking – a review. J. Food Eng. 86, 465–474 (2008).
Pathare, P. B. & Roskilly, A. P. Quality and energy evaluation in meat cooking. Food Eng. Rev. 8, 435–447 (2016).
Sruthi, N. U., Premjit, Y., Pandiselvam, R., Kothakota, A. & Ramesh, S. V. An overview of conventional and emerging techniques of roasting: effect on food bioactive signatures. Food Chem. 348, 129088 (2021).
Wang, X. et al. Continuous 2000 K droplet-to-particle synthesis. Mater. Today 35, 106–114 (2020).
FDA, U. Refrigerator & freezer storage chart. https://www.fda.gov/media/74435/download (2018).
Cuesta, A., Dhamelincourt, P., Laureyns, J., Martínez-Alonso, A. & Tascón, J. M. D. Raman microprobe studies on carbon materials. Carbon 32, 1523–1532 (1994).
Ferrari, A. C. & Robertson, J. Interpretation of Raman spectra of disordered and amorphous carbon. Phys. Rev. B 61, 14095–14107 (2000).
Baranyi, J. & Roberts, T. A. A dynamic approach to predicting bacterial growth in food. Int. J. Food Microbiol. 23, 277–294 (1994).
Eifert, J. D., Foods, N. A. C. on M. C. for, & others. Microbiological testing by industry of ready-to-eat foods under FDA’s jurisdiction for pathogens (or appropriate indicator organisms): Verification of preventive controls. https://www.fsis.usda.gov/sites/default/files/media_file/2021-07/NACMCF_2018-2020_RTETesting.pdf (2022).
Sha, L. & Xiong, Y. L. Plant protein-based alternatives of reconstructed meat: science, technology, and challenges. Trends Food Sci. Technol. 102, 51–61 (2020).
Hamann, D. D. & Macdonald, G. A. Rheology and Texture Properties of Surimi-Based Food. In Surimi Technology (eds. Lanie, T. C. & Lee, C. M.) 429–500 (Marcel Dekker, 1992).
Schreuders, F. K. G., Sagis, L. M. C., Bodnár, I., Boom, R. M. & van der Goot, A. J. Non-linear rheology reveals the importance of elasticity in meat and meat analogues. Sci. Rep. 12, 1334 (2022).
Wang, L., Zhang, Y. & Feng, J. On the Euclidean distance of images. IEEE Trans. Pattern Anal. Mach. Intell. 27, 1334–1339 (2005).
Govindarajan, S. & Snyder, H. E. Fresh meat color. C R C Crit. Rev. Food Technol. 4, 117–140 (1973).
Seideman, S. C., Cross, H. R., Smith, G. C. & Durland, P. R. Factors associated with fresh meat color: a review. J. Food Qual. 6, 211–237 (1984).
Brewer, S. Irradiation effects on meat color – a review. Meat Sci. 68, 1–17 (2004).
ten Brink, B., Damink, C., Joosten, H. M. L. J. & Huis in’t Veld, J. H. J. Occurrence and formation of biologically active amines in foods. Int. J. Food Microbiol. 11, 73–84 (1990).
Gill, C. O. Meat spoilage and evaluation of the potential storage life of fresh meat. J. Food Prot. 46, 444–452 (1983).
Aykın-Dinçer, E. & Erbaş, M. Effect of packaging method and storage temperature on quality properties of cold-dried beef slices. LWT 124, 109171 (2020).
Hopkins, D. L. et al. The effect of pH decline rate on the meat and eating quality of beef carcasses. Anim. Prod. Sci. 54, 407–413 (2014).
Page, J. K., Wulf, D. M. & Schwotzer, T. R. A survey of beef muscle color and pH. J. Anim. Sci. 79, 678–687 (2001).
Holman, B. W. B. et al. The association between total volatile basic nitrogen (TVB-N) concentration and other biomarkers of quality and spoilage for vacuum packaged beef. Meat Sci. 179, 108551 (2021).
Bekhit, A. E.-D. A., Holman, B. W. B., Giteru, S. G. & Hopkins, D. L. Total volatile basic nitrogen (TVB-N) and its role in meat spoilage: a review. Trends Food Sci. Technol. 109, 280–302 (2021).
Bekhit, A. E.-D. A., Giteru, S. G., Holman, B. W. B. & Hopkins, D. L. Total volatile basic nitrogen and trimethylamine in muscle foods: potential formation pathways and effects on human health. Compr. Rev. Food Sci. Food Saf. 20, 3620–3666 (2021).
Sperber, W. H. Influence of water activity on foodborne bacteria — a review. J. Food Prot. 46, 142–150 (1983).
Tapia, M. S., Alzamora, S. M. & Chirife, J. Effects of water activity (a w) on microbial stability as a hurdle in food preservation. In Water Activity in Foods 323–355 (John Wiley & Sons, Ltd, 2020).
Cilla, I., Martínez, L., Beltrán, J. A. & Roncalés, P. Dry-cured ham quality and acceptability as affected by the preservation system used for retail sale. Meat Sci. 73, 581–589 (2006).
Barbut, S. & Findlay, C. j. Influence of sodium, potassium and magnesium chloride on thermal properties of beef muscle. J. Food Sci. 56, 180–182 (1991).
Bircan, C. & Barringer, S. A. Determination of protein denaturation of muscle foods using the dielectric properties. J. Food Sci. 67, 202–205 (2002).
Mesias, M., Delgado-Andrade, C., Holgado, F. & Morales, F. J. Acrylamide in French fries prepared at primary school canteens. Food Funct. 11, 1489–1497 (2020).
Ndraha, N., Hsiao, H.-I., Vlajic, J., Yang, M.-F. & Lin, H.-T. V. Time-temperature abuse in the food cold chain: review of issues, challenges, and recommendations. Food Control 89, 12–21 (2018).
Acknowledgements
LH acknowledges the support from the University of Maryland A. James Clark School of Engineering. The identification of any commercial product or trade name does not imply endorsement or recommendation by the National Institute of Standards and Technology.
Author information
Authors and Affiliations
Contributions
L.H. directed the project. Y.M. and L.H. conceptualized the invention. Y.M., P.M., T.L. and L.H. designed the experiments. P.M., T.L., Y.M., S.L. and G.C. carried out flashing heating experiments. P.M., X.J. and B.Z. performed microbiological tests. H.L., X.Z. and Y.M. carried out thermal analysis. S.O.R. performed food toxicity tests. P.M. carried out microscopy and chromatography experiments, and meat texture analysis. Y.M. and M.Z. carried out spectroscopic measurements. P.M. and Y.M. carried out histology study. H.X. and X.W. performed high-speed video shooting. R.T. advised the application of the UFH method to meat products. Y.M., P.M., H.L., A.H.B., Y.L., R.T., C.-I.W., Q.W., R.M.B. and L.H. conducted collaborative writing.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Peer review
Peer review information
Nature Communications thanks Olivier Couvert, Alfredo Palop, and the other, anonymous, reviewer(s) for their contribution to the peer review of this work. A peer review file is available.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Source data
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Mao, Y., Ma, P., Li, T. et al. Flash heating process for efficient meat preservation. Nat Commun 15, 3893 (2024). https://doi.org/10.1038/s41467-024-47967-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-024-47967-1
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.