All Questions
Tagged with measurement capacitor
38
questions
1
vote
0
answers
37
views
Comparison of two methods used to calculate capacitance
I need to compare two potential methods used to calculate capacitance, but I can't find the names for them to do some research.
The first method: Placing a capacitor in a circuit with an 800 Hz ...
0
votes
1
answer
85
views
Capacitor test mode in ICT
My ICT machine has two capacitor measurement modes on the PCB:
Mode 1: Use DC source test method (Figure 1)
Mode 2: Use AC source test method (Figure 2)
Could anyone please help me with the ...
12
votes
6
answers
6k
views
Why can't capacitors on PCBs be measured with a multimeter?
While looking at this article, it mentioned that one cannot test the capacitance of a capacitor while it is on a PCB. The explanation given is:
The reason is, that when a capacitor is inside the ...
9
votes
1
answer
340
views
Why does the measured capacitance value of some ceramic capacitors keeps on increasing?
The capacitance of two ceramic capacitors were measured using an LCR meter (Agilent E4980A) at 1 kHz. The measured capacitance values of 100 pF and 100 nF capacitors are shown below.
The value of 100 ...
0
votes
1
answer
204
views
How does the FDC1004 (capacitance to digital converter) measure capacitance?
I am using the FDC1004 and wondering how it exactly measures capacitance. The datasheet is not explaining much. An associated application note contains a little more information, but still very little ...
0
votes
1
answer
50
views
Testing for connection using capacitors
I work in a common mode choke coil manufacturing company. They often measure the insulation resistance as well as the connectivity of the coils. I have a good understanding of how insulation ...
0
votes
0
answers
157
views
PCap04 initialisation sequence
I'm developing SPI interface with a very complex and badly documented PCap04 device. I've already implemented and tested all commands, but the results are always very unstable. Even the charging/...
-2
votes
1
answer
118
views
Voltage across capacitor measured in parallel, why not showing Vc?
I am trying to understand something and missing something. In a low pass RC filter, the output is connected in parallel with the capacitor, right, and is phase shifted, because the current in a RC ...
2
votes
1
answer
349
views
How to measure capacitor value using an LC circuit?
How would I measure the value of capacitor using an inductor of unknown value but with a function generator producing a sine wave of 1MHz?
I have an oscilloscope handy.
I lost the labelling on the ...
0
votes
2
answers
115
views
How do I calculate the capacity of a capacitor using measurements of an experiment?
I build this circuit in an experiment
During the experiment I got these readings:
...
-1
votes
1
answer
115
views
Custom Test Fixture for LCR meter
I've designed and built a custom test fixture (based on Keysight's 16047A) to be able to measure multiple pin capacitors.
When testing it to compare both fixtures (the custom and the original), I ...
7
votes
3
answers
13k
views
How do digital multimeters measure capacitance?
How do digital mulitimeters (DMM) measure capacitance through their typical 10M Ohm input/output impedance?
Providing a logic level of 3.3V, attempting to measure 1F would mean a time constant of ...
0
votes
2
answers
394
views
Measuring 0805 Capacitor values under 1nF
Other than investing in an expensive tweezer type meter for SMD components, what would be a good method for the layman to find the capacitance of an 0805 ceramic capacitor whose value is below 1nF? My ...
0
votes
3
answers
663
views
Why does the capacitance of ceramic capacitors change with test measurement voltage change?
I faced a problem of measuring capacity in ceramic capacitors.
Measurements did with Smart Tweezers ST5S. It has two output voltage levels that can be selected: 0.45 Vrms and 0.9 Vrms.
The capacitor ...
8
votes
3
answers
4k
views
Measuring resistance of a capacitor - unexpected results
I'm trying to measure the impedance (\$R_x\$) of C1 in the RC circuit shown below, but I'm getting some results I can't explain.
simulate this circuit – Schematic created using CircuitLab
...