Questions tagged [cable-assemblies]
The cable-assemblies tag has no usage guidance.
82
questions
1
vote
1
answer
48
views
Cable type selection for 128 channel signal transfer [closed]
I want to use a cable to be connected (soldered) to my PCB, my PCB has 128 pads on it as follows:
The signal that will be transfer to cable is @3 MHz to 6 MHZ, in range of 150 uA.
The width of the ...
- 511
0
votes
0
answers
40
views
Cable layout for multiple motors and encoders
I need to make a connection between 2 PCBs, the first is a controller board with microcontroller, motor drivers and other peripherals. The second is a motor/encoder board, essentially a three motor ...
- 1
0
votes
0
answers
53
views
Wire Harness Schematic : Use of Brackets between conductors
I have looked add several documents concerning themself with wire harness schematics. I am having a hard time identifying the meaning of the brackets between several individual conductors tied to a ...
- 101
0
votes
1
answer
56
views
What are the outputs from my cable?
I am in the process of building a microphone connected to a Raspberry Pi Pico. To check my expectations are correct, I have bought a pre-assembled electret mic and amplifier. The issue I have, is I ...
- 61
1
vote
1
answer
60
views
Fixing SMB adjustable contact to its SMB connector (Jack)
I recently purchased an SMB adjustable square flange jack connector: R114413000 [Partlink].
In the bag, I receive the adjustable contact and the connector:
How do I fix this adjustable contact to the ...
- 65
3
votes
1
answer
339
views
Can you separate the D+/D- wires from the GND/Vcc wires in a USB 2.0 cable?
I am currently designing a wiring loom which includes USB 2.0 cable within it. It is critical that the thickness of this leg is as thin as possible due to the constraints of my client. Unfortunately, ...
- 33
0
votes
1
answer
47
views
Using USB C 3.x cables with an E-mark chip for non-USB applications
I was looking for a multi-pin cable assembly that is push-pull capable, shielded, has dedicated power lines and multiple twisted pair cables inside. The idea is to use these cables to power ...
- 75
-1
votes
2
answers
104
views
Which file format is commonly used for custom-made cabling?
I'm in the situation to need custom-made cabling to connect my Raspi to a bunch of peripherals. I used Fritzing to design the cable harness (see the rendering below),…
… but apparently, my favorite ...
- 575
6
votes
0
answers
210
views
Identify kind of cable with markings such as "WE-B 2 PAIR" on the jacket
While cleaning out our back yard shed, I came across a coil of cable of a kind that I have never seen before (image below). It was left here by the previous home owner, who worked in some kind of ...
- 161
1
vote
1
answer
72
views
Is there a standard for JST/Molex low voltage digital connector pin configuration?
I am wondering if there is a standard for JST/Molex cable assemblies' pin configuration.
I know there are three types of ethernet/CAT cables: Straight, Cross-over and Rollover.
Does something like ...
- 41
1
vote
1
answer
88
views
Twisted pairs incompatible with very slow ground-referenced signals?
I am stumped by the behavior of a cable assembly I have made out of a pair of repurposed ethernet cables, and am hoping you can help me rule out issues that may be caused by twisted pairs. I realize ...
- 411
4
votes
1
answer
136
views
HP 8568B J1 Connector identification
Can anyone identify these 4 individual RF connectors? I think it's some sort of RP-SMB, but it could be something more foreign. I would need to buy 4 cables to connect up the spectrum analyzer.
...
- 95
1
vote
2
answers
1k
views
How to terminate shielded cables between PCBs?
I have an electronic system design with lots of off-board data/power connections to various peripheral components (sensors, LEDs, motors). This is all contained within a large enclosure that is ...
- 618
0
votes
1
answer
74
views
How do I connect micro Molex to nano Molex socket?
I have a Molex cable that has a bigger size than its socket. My problem is how do I connect the cable to its socket?
I sent this picture about comparison cable and the nano socket exactly in front of ...
0
votes
1
answer
102
views
What connector is this on the Eachine E160 flight control board?
I'm trying to find the exact type of this 3-pin clippy connector - I need another one to connect the SBUS signal to the board:
Measures:
Pitch: ~1mm
Total width: ~6mm
Total height: ~3mm
I've been ...
- 103