Shift: (Candidates must be available for all shifts) 1st Shift – 6AM-4PM, 2nd Shift – 2PM-10PM, 3rd Shift – 8PM-6AM
Interview Required
Worker I – Inserter, Demolders, Inspect/Repair, & Pack/Trim
Basic Function: Performs general labor as assigned.
If demolding: Removes finished foam seating pads from their molds, places parts on a conveyer for the next stage of the finishing process and removes any obvious foam particles from the molds.
If waxing: Removes any obvious foam particles from molds and applies a thin layer of demolding agent (aerosol wax) to the surface of the molds.
If placing inserts:
Qualifications: Skills, Education and Training
Required
Environmental management system overview
Orientation
Quality Management System Overview
Right-to-Know/Hazardous Communication
Verified by Reference Check or Job Performance
Able to work in team setting and communicate well
Physically able to perform job
Follows both oral and written instructions, including customer standards.
Reliable
Able to work any shift and overtime as directed
Follows good safety practices.
If Waxing:
Able to operate and properly calibrate aerosol wax gun
Must be proficient in knowledge and application of all applicable standards and work instructions pertaining to the specific parts assigned.
If Repairing:
All positions clean work area during periods of downtime and at the conclusion of shift and perform various duties assigned by supervisor.
Performs production-related duties as assigned:
Waxing:
Cleans foam particles and/or wax build-up from molds
Applies spray wax to the mold surfaces
Notifies supervisor and line technician of process problems
Placing Inserts:
Places proper inserts (wires, felts, & Velcro) into molds.
Informs supervisor of insert shortages; assists in recovering dropped or misplaced inserts
Demolding:
Removes molded foam seat pads from molds.
Places part on conveyer for next stage of finishing process.
Cleans any foam particles and/or wax build-up from the molds.
Informs supervisor and line technician of process problems underfills, wax burns, etc.
Trimming:
Removes all ribbon vents and uncontrolled flash on parting line that is greater than 25mm using scissors or air trimmer tool.
Inspects parts for the following defects.
Flash not trimmed off.
Hard spots on the parting line.
Under fills
Foam free areas
Safety glove must be worn on opposite hand.
Inform supervisor of B-surface defects.
See specialized customer required trim areas.
Repairing:
Look for voids marked by Inspector.
Use scoop to repair.
If voids are small, stuff the void with repair foam, then cut it back to contour of part.
Inform supervisor of any insert shortages
Packing:
Remove parts off the monorail.
Identify part, place it in its respective bin
Pack the parts in their respective order. The pack description is posted on the floor where the bins go.
Pack description includes the part orientation
Pack description includes the quantity
Pack description includes the part number and the vehicle
Verify that the standard pack is met.
Verify the correct quantity is in the bin
Verify that the pack orientation is correct
Make sure that all parts are inside of the bin. Parts that hang out of the bin may get ripped.
Notify production supervisor if out of balance on parts.
As backup to material clerk, prepare and attach product labels.
Mold Cleaning:
Clean the bowl of the tool.
Clean all ribbon vents of any foam
Clean any areas that have foam stuck to them
Apply paste wax to any areas scrubbed with a chore boy or had stuck foam
Clean all wire holders of foam.
Apply paste wax to wire holders that have stuck foam
Vent Identification
Ribbon Vent
Verify the bowl is clean.
Inspect the ribbon vents to ensure they are free of flash
Inspect all wire holders to ensure they are foam free. A foamed in holde
Company Description
Intellyk is a Joint Commission Certified global staff augmentation firm providing a wide-range of talent on-demand and total workforce solutions. To know more about Intellyk, please visit our website www.intellyk.com.
We are constantly on the lookout for professionals to fulfil the staffing needs of our clients, and we currently have a job opening that may interest you.
Intellyk is a Joint Commission Certified global staff augmentation firm providing a wide-range of talent on-demand and total workforce solutions. To know more about Intellyk, please visit our website www.intellyk.com. We are constantly on the lookout for professionals to fulfil the staffing needs of our clients, and we currently have a job opening that may interest you.
Seniority level
Entry level
Employment type
Full-time
Job function
Marketing, Public Relations, and Writing/Editing
Industries
IT Services and IT Consulting
Referrals increase your chances of interviewing at Intellyk Inc. by 2x