Abstract
Plastic pyrolysis technology, as an efficient and stable path for chemical recycling of waste plastics, alleviates current energy pressures and solves the problem of continuous accumulation of waste plastics in the environment. At present, the vast majority of research on plastic pyrolysis is focused on how to improve the yield and quality of liquid fuels, while there is generally little research on the gases generated by plastic pyrolysis. However, gases such as H2, CH4, and light hydrocarbons generated during pyrolysis also have high utilization value, and have very considerable application prospects in chemical, aerospace, and metallurgical fields. In addition, compared with the separation difficulties of liquid products, the treatment of gas products is easier and more conducive to subsequent utilization. This article discusses and analyzes the yield and composition of gases generated by plastic in three different pyrolysis methods: direct pyrolysis, catalytic pyrolysis, and microwave pyrolysis. Compared to traditional direct pyrolysis, catalytic pyrolysis and microwave pyrolysis can treat plastic waste more efficiently and energy-efficient, and have higher gas yields. This article also discusses various factors such as temperature that influence the formation of gas products and their importance. Finally, the challenges faced are proposed, aiming to provide reference and direction for future research on improving the yield of gas generated by plastic pyrolysis.
Similar content being viewed by others
Data availability
Data sharing is not applicable to this article as no new data were created or analyzed in this study.
References
G. Lopez, M. Artetxe, M. Amutio, J. Bilbao, M. Olazar, Thermochemical routes for the valorization of waste polyolefinic plastics to produce fuels and chemicals. A review. Renew. Sustain. Energy Rev. 73, 346–368 (2017)
S. Kartik, H.K. Balsora, M. Sharma, A. Saptoro, R.K. Jain, J.B. Joshi et al., Valorization of plastic wastes for production of fuels and value-added chemicals through pyrolysis—a review. Thermal Sci. Eng. Progress 32, 101316 (2022)
M.M. Ismail, I. Dincer, A new renewable energy based integrated gasification system for hydrogen production from plastic wastes. Energy 270, 126869 (2023)
D.S. Achilias, C. Roupakias, P. Megalokonomos, A.A. Lappas, E.V. Antonakou, Chemical recycling of plastic wastes made from polyethylene (LDPE and HDPE) and polypropylene (PP). J. Hazard. Mater. 149, 536–542 (2007)
G. Celik, R.M. Kennedy, R.A. Hackler, M. Ferrandon, A. Tennakoon, S. Patnaik et al., Upcycling single-use polyethylene into high-quality liquid products. ACS Cent. Sci. 5, 1795–1803 (2019)
D.C. Ashworth, P. Elliott, M.B. Toledano, Waste incineration and adverse birth and neonatal outcomes: a systematic review. Environ. Int. 69, 120–132 (2014)
D.-D. Yao, C.-H. Wang, Pyrolysis and in-line catalytic decomposition of polypropylene to carbon nanomaterials and hydrogen over Fe- and Ni-based catalysts. Appl. Energy 265, 114819 (2020)
M. Franchini, M. Rial, E. Buiatti, F. Bianchi, Health effects of exposure to waste incinerator emissions: a review of epidemiological studies. Annali dell’Istituto Superiore di Sanita 40, 101–115 (2005)
N. Yang, H. Zhang, M. Chen, L.-M. Shao, P.-J. He, Greenhouse gas emissions from MSW incineration in China: impacts of waste characteristics and energy recovery. Waste Manage. 32, 2552–2560 (2012)
E.L. Teuten, J.M. Saquing, D.R.U. Knappe, M.A. Barlaz, S. Jonsson, A. Bjorn et al., Transport and release of chemicals from plastics to the environment and to wildlife. Philos. Trans. R. Soc. B: Biol. Sci. 364, 2027–2045 (2009)
J.-P. Lange, Managing plastic waste─sorting, recycling, disposal, and product redesign. ACS Sustai. Chem. Eng. 9, 15722–15738 (2021)
K. Ragaert, L. Delva, K. Van Geem, Mechanical and chemical recycling of solid plastic waste. Waste Manage. 69, 24–58 (2017)
R.K. Singh, B. Ruj, A.K. Sadhukhan, P. Gupta, Conventional pyrolysis of plastic waste for product recovery and utilization of pyrolytic gases for carbon nanotubes production. Environ. Sci. Pollut. Res. 29, 20007–20016 (2022)
K.K. Jha, T.T.M. Kannan, Alternate fuel preparation in low cost from waste plastic: a review. Mater. Today: Proc. 37, 3656–3657 (2021)
S.D. Anuar Sharuddin, F. Abnisa, W.M.A. Wan Daud, M.K. Aroua, A review on pyrolysis of plastic wastes. Energy Convers. Manage. 115, 308–326 (2016)
B. Kunwar, H.N. Cheng, S.R. Chandrashekaran, B.K. Sharma, Plastics to fuel: a review. Renew. Sustain. Energy Rev. 54, 421–428 (2016)
S.L. Wong, N. Ngadi, T.A.T. Abdullah, Current state and future prospects of plastic waste as source of fuel: a review. Renew. Sustain. Energy Rev. 50, 1167–1180 (2015)
X.Q. Jia, C. Qin, T. Friedberger, Z.B. Guan, Z. Huang, Efficient and selective degradation of polyethylenes into liquid fuels and waxes under mild conditions. Sci. Adv. 2, e1501591 (2016)
TPE magazine international Group, Plastics - the Facts 2017. An analysis of European plastics production, demand and waste data. TPE Mag. Int. 9, 93 (2018)
AIE. The future of petrochemicals: Towards more sustainable plastics and fertilisers. International Energy Agency 2018.
R. Geyer, J.R. Jambeck, K.L. Law, Production, use, and fate of all plastics ever made. Sci. Adv. 3, e1700782 (2017)
F.M. Tsai, T.D. Bui, M.L. Tseng, M.K. Lim, J.Y. Hu, Municipal solid waste management in a circular economy: a data-driven bibliometric analysis. J. Clean. Prod. 275, 124132 (2020)
M.A. Charitopoulou, K.G. Kalogiannis, A.A. Lappas, D.S. Achilias, Novel trends in the thermo-chemical recycling of plastics from WEEE containing brominated flame retardants. Environ. Sci. Pollut. Res. Int. 28, 59190–59213 (2021)
A. Ramos, A. Rouboa, Renewable energy from solid waste: life cycle analysis and social welfare. Environ. Impact Assess. Rev. 85, 106469 (2020)
J.A. Onwudili, N. Insura, P.T. Williams, Composition of products from the pyrolysis of polyethylene and polystyrene in a closed batch reactor: effects of temperature and residence time. J. Anal. Appl. Pyrol. 86, 293–303 (2009)
X.H. Zhao, M. Korey, K. Li, K. Copenhaver, H. Tekinalp, S. Celik et al., Plastic waste upcycling toward a circular economy. Chem. Eng. J. 428, 131928 (2022)
X. Hu, H.Y. Guo, M. Gholizadeh, B. Sattari, Q. Liu, Pyrolysis of different wood species: Impacts of C/H ratio in feedstock on distribution of pyrolysis products. Biomass Bioenerg. 120, 28–39 (2019)
P.H.M. Putra, S. Rozali, M.F.A. Patah, A. Idris, A review of microwave pyrolysis as a sustainable plastic waste management technique. J. Environ. Manage. 303, 114240 (2022)
A. Marcilla, M.I. Beltran, R. Navarro, Thermal and catalytic pyrolysis of polyethylene over HZSM5 and HUSY zeolites in a batch reactor under dynamic conditions. Appl. Catal. B 86, 78–86 (2009)
M. Artetxe, G. Lopez, M. Amutio, I. Barbarias, A. Arregi, R. Aguado et al., Styrene recovery from polystyrene by flash pyrolysis in a conical spouted bed reactor. Waste Manage. 45, 126–133 (2015)
B.S. Kang, S.G. Kim, J.S. Kim, Thermal degradation of poly(methyl methacrylate) polymers: kinetics and recovery of monomers using a fluidized bed reactor. J. Anal. Appl. Pyrol. 81, 7–13 (2008)
Y. Mo, L. Zhao, Z.H. Wang, C.L. Chen, G.Y.A. Tan, J.Y. Wang, Enhanced styrene recovery from waste polystyrene pyrolysis using response surface methodology coupled with Box-Behnken design. Waste Manage. 34, 763–769 (2014)
F. Obeid, J. Zeaiter, A.H. Al-Muhtaseb, K. Bouhadir, Thermo-catalytic pyrolysis of waste polyethylene bottles in a packed bed reactor with different bed materials and catalysts. Energy Convers. Manage. 85, 1–6 (2014)
W.C. Huang, M.S. Huang, C.F. Huang, C.C. Chen, K.L. Ou, Thermochemical conversion of polymer wastes into hydrocarbon fuels over various fluidizing cracking catalysts. Fuel 89, 2305–2316 (2010)
J. Zeaiter, A process study on the pyrolysis of waste polyethylene. Fuel 133, 276–282 (2014)
Q. Zhou, L. Zheng, Y.Z. Wang, G.M. Zhao, B. Wang, Catalytic degradation of low-density polyethylene and polypropylene using modified ZSM-5 zeolites. Polym. Degrad. Stab. 84, 493–497 (2004)
M.R. Hernandez, A.N. Garcia, A. Marcilla, Catalytic flash pyrolysis of HDPE in a fluidized bed reactor for recovery of fuel-like hydrocarbons. J. Anal. Appl. Pyrol. 78, 272–281 (2007)
S.H. Jung, M.H. Cho, B.S. Kang, J.S. Kim, Pyrolysis of a fraction of waste polypropylene and polyethylene for the recovery of BTX aromatics using a fluidized bed reactor. Fuel Process. Technol. 91, 277–284 (2010)
P.T. Williams, E.A. Williams, Fluidised bed pyrolysis of low density polyethylene to produce petrochemical feedstock. J. Anal. Appl. Pyrol. 51, 107–126 (1999)
M.H. Cho, S.H. Jung, J.S. Kim, Pyrolysis of mixed plastic wastes for the recovery of benzene, toluene, and xylene (BTX) aromatics in a fluidized bed and chlorine removal by applying various additives. Energy Fuels 24, 1389–1395 (2010)
S.V. Papuga, P.M. Gvero, L.M. Vukic, Temperature and time influence on the waste plastics pyrolysis in the fixed bed reactor. Therm. Sci. 20, 731–741 (2016)
H. Zhou, C.F. Wu, J.A. Onwudili, A.H. Meng, Y.G. Zhang, P.T. Williams, Polycyclic aromatic hydrocarbons (PAH) formation from the pyrolysis of different municipal solid waste fractions. Waste Manage. 36, 136–146 (2015)
G. Grause, S. Matsumoto, T. Kameda, T. Yoshioka, Pyrolysis of mixed plastics in a fluidized bed of hard burnt lime. Ind. Eng. Chem. Res. 50, 5459–5466 (2011)
Ghosh P, Sengupta S, Singh L, Sahay A. Life cycle assessment of waste-to-bioenergy processes: a review. Bioreactors 2020; 105–122.
D. Almeida, M.D. Marques, Thermal and catalytic pyrolysis of plastic waste. Polimeros-Ciencia e Tecnologia 26, 44–51 (2015)
G. Elordi, M. Olazar, G. Lopez, M. Artetxe, J. Bilbao, Product yields and compositions in the continuous pyrolysis of high-density polyethylene in a conical spouted bed reactor. Ind. Eng. Chem. Res. 50, 6650–6659 (2011)
C.M. Simon, W. Kaminsky, Chemical recycling of polytetrafluoroethylene by pyrolysis. Polym. Degrad. Stab. 62, 1–7 (1998)
C. Berrueco, F.J. Mastral, E. Esperanza, J. Ceamanos, Production of waxes and tars from the continuous pyrolysis of high density polyethylene. Influence of operation variables. Energy Fuels 16, 1148–1153 (2002)
J.F. Mastral, C. Berrueco, J. Ceamanos, Pyrolysis of high-density polyethylene in free-fall reactors in series. Energy Fuels 20, 1365–1371 (2007)
M. Rehan, A.S. Nizami, O. Taylan, B.O. Al-Sasi, A. Demirbas, Determination of wax content in crude oil. Pet. Sci. Technol. 34, 799–804 (2016)
Y.H. Lin, H.Y. Yen, Fluidised bed pyrolysis of polypropylene over cracking catalysts for producing hydrocarbons. Polym. Degrad. Stab. 89, 101–108 (2005)
X.S. Zhang, H.W. Lei, G. Yadavalli, L. Zhu, Y. Wei, Y.P. Liu, Gasoline-range hydrocarbons produced from microwave-induced pyrolysis of low-density polyethylene over ZSM-5. Fuel 144, 33–42 (2015)
P. Senthil Kumar, M. Bharathikumar, C. Prabhakaran, S. Vijayan, K. Ramakrishnan, Conversion of waste plastics into low-emissive hydrocarbon fuels through catalytic depolymerization in a new laboratory scale batch reactor. Int. J. Energy Environ. Eng. 8, 167–173 (2017)
S. Devasahayam, Review: opportunities for simultaneous energy/materials conversion of carbon dioxide and plastics in metallurgical processes. Sustain. Mater. Technol. 22, e00119 (2019)
J. Schirmer, J.S. Kim, E. Klemm, Catalytic degradation of polyethylene using thermal gravimetric analysis and a cycled-spheres-reactor. J. Anal. Appl. Pyrol. 60, 205–217 (2001)
J. Aguado, D.P. Serrano, M.G. San, Feedstock recycling of polyethylene in a two-step thermo-catalytic reaction system. J. Anal. Appl. Pyrol. 79, 415–423 (2008)
P.J. Donaj, W. Kaminsky, F. Buzeto, W. Yang, Pyrolysis of polyolefins for increasing the yield of monomers’ recovery. Waste Manage. 32, 840–846 (2012)
S. Chaianansutcharit, R. Katsutath, A. Chaisuwan, T. Bhaskar, A. Nigo, A. Muto et al., Catalytic degradation of polyolefins over hexagonal mesoporous silica: effect of aluminum addition. J. Anal. Appl. Pyrol. 80, 360–368 (2007)
K. Moorthy Rajendran, V. Chintala, A. Sharma, S. Pal, J.K. Pandey, P. Ghodke, Review of catalyst materials in achieving the liquid hydrocarbon fuels from municipal mixed plastic waste (MMPW). Mater. Today Commun. 24, 100982 (2020)
S.M. Al-Salem, A. Antelava, A. Constantinou, G. Manos, A. Dutta, A review on thermal and catalytic pyrolysis of plastic solid waste (PSW). J. Environ. Manage. 197, 177–198 (2017)
M. Boronat, A. Corma, Are carbenium and carbonium ions reaction intermediates in zeolite-catalyzed reactions? Appl. Catal. A 336, 2–10 (2008)
C. Muhammad, J.A. Onwudili, P.T. Williams, Catalytic pyrolysis of waste plastic from electrical and electronic equipment. J. Anal. Appl. Pyrol. 113, 332–339 (2015)
M.R. Hernandez, A. Gomez, A.N. Garcia, J. Agullo, A. Marcilla, Effect of the temperature in the nature and extension of the primary and secondary reactions in the thermal and HZSM-5 catalytic pyrolysis of HDPE. Appl. Catal. A General 317, 183–194 (2007)
S.S.Z. Salmasi, M.S. Abbas-Abadi, M.N. Haghighi, H. Abedini, The effect of different zeolite based catalysts on the pyrolysis of poly butadiene rubber. Fuel 160, 544–548 (2015)
G. Elordi, M. Olazar, G. Lopez, Catalytic pyrolysis of HDPE in continuous mode over zeolite catalysts in a conical spouted bed reactor. J. Anal. Appl. Pyrol. 85, 345–351 (2009)
G. Manos, A. Garforth, J. Dwyer, Catalytic degradation of high-density polyethylene over different zeolitic structures. Ind. Eng. Chem. Res. 39, 1198–1202 (2000)
J.W. Park, J.H. Kim, G. Seo, The effect of pore shape on the catalytic performance of zeolites in the liquid-phase degradation of HDPE. Polym. Degrad. Stab. 76, 495–501 (2002)
M. Syamsiro, H. Saptoadi, T. Norsujianto, P. Noviasri, S. Cheng, Z. Alimuddin et al., Fuel oil production from municipal plastic wastes in sequential pyrolysis and catalytic reforming reactors. Energy Procedia 47, 180–188 (2014)
K.H. Lee, Effects of the types of zeolites on catalytic upgrading of pyrolysis wax oil. J. Anal. Appl. Pyrol. 94, 209–214 (2012)
G. Elordi, M. Olazar, M. Artetxe, P. Castano, J. Bilbao, Effect of the acidity of the HZSM-5 zeolite catalyst on the cracking of high density polyethylene in a conical spouted bed reactor. Appl. Catal. A 415–416, 89–95 (2012)
C. Vasile, H. Pakdel, B. Mihai, Thermal and catalytic decomposition of mixed plastics. J. Anal. Appl. Pyrol. 57, 287–303 (2001)
J. Jae, G.A. Tompsett, A.J. Foster, Investigation into the shape selectivity of zeolite catalysts for biomass conversion. J. Catal. 279, 257–268 (2011)
K. Sun, Q.X. Huang, Y. Chi, J.H. Yan, Effect of ZnCl2-activated biochar on catalytic pyrolysis of mixed waste plastics for producing aromatic-enriched oil. Waste Manage. 81, 128–137 (2018)
Y.L. Sun, Y. Ma, S.Y. Li, C.T. Yue, Research progress in pyrolysis and catalytic pyrolysis of polyolefin plastics. Chem. Ind. Eng. Progress 40, 2784–2801 (2021)
Y. Sakata, M. Azhar Uddin, A. Muto, Y. Kanada, K. Koizumi, K. Murata, Catalytic degradation of polyethylene into fuel oil over mesoporous silica (KFS-16) catalyst. J. Anal. Appl. Pyrol. 43, 15–25 (1997)
Y. Sakata, M. Azhar Uddin, A. Muto, Degradation of polyethylene and polypropylene into fuel oil by using solid acid and non-acid catalysts. J. Anal. Appl. Pyrol. 51, 135–155 (1999)
K.N. Aishwarya, S. Nangarthody, Microwave assisted pyrolysis of plastic waste. Procedia Technol. 25, 990–997 (2016)
J. Sun, W.L. Wang, Q.Y. Yue, Review on microwave-matter interaction fundamentals and efficient microwave-associated heating strategies. Materials 9, 231 (2016)
L.L. Fan, Y.N. Zhang, S.Y. Liu, N. Zhou, P. Chen, Y.H. Liu et al., Ex-situ catalytic upgrading of vapors from microwave-assisted pyrolysis of low-density polyethylene with MgO. Energy Convers. Manage. 149, 432–441 (2017)
N. Zhou, L.L. Dai, Y.C. Lv, H. Li, W.Y. Deng, F.Q. Guo et al., Catalytic pyrolysis of plastic wastes in a continuous microwave assisted pyrolysis system for fuel production. Chem. Eng. J. 418, 129412 (2021)
M.Q. Dai, H. Xu, Z.S. Yu, S.W. Fang, L. Chen, W.L. Gu et al., Microwave-assisted fast co-pyrolysis behaviors and products between microalgae and polyvinyl chloride. Appl. Therm. Eng. 136, 9–15 (2018)
Z. Liu, H.Q. Wang, X.D. Zhang, J.W. Liu, Y.Y. Zhou, Dechlorination of organochloride waste mixture by microwave irradiation before forming solid recovered fuel. Waste Manage. 62, 118–124 (2017)
A. Undri, M. Frediani, L. Rosi, P. Frediani, Reverse polymerization of waste polystyrene through microwave assisted pyrolysis. J. Anal. Appl. Pyrol. 105, 35–42 (2014)
A. Undri, L. Rosi, M. Frediani, P. Frediani, Efficient disposal of waste polyolefins through microwave assisted pyrolysis. Fuel 116, 662–671 (2014)
A. Aboulkas, K. El Harfi, A. El Bouadili, Thermal degradation behaviors of polyethylene and polypropylene. Part I: Pyrolysis kinetics and mechanisms. Energy Convers. Manage. 51, 1363–1369 (2010)
P. Rex, I.P. Masilamani, L.R. Miranda, Microwave pyrolysis of polystyrene and polypropylene mixtures using different activated carbon from biomass. J. Energy Inst. 93, 1819–1832 (2020)
E. Khaghanikavkani, M.M. Farid, J. Holdem, A. Williamson, Microwave pyrolysis of plastic. J. Chem. Eng. Process Technol. (2013). https://doi.org/10.4172/2157-7048.1000150
K. Ding, S.S. Liu, Y. Huang, S.Y. Liu, N. Zhou, P. Peng et al., Catalytic microwave-assisted pyrolysis of plastic waste over NiO and HY for gasoline-range hydrocarbons production. Energy Convers. Manage. 196, 1316–1325 (2019)
L.L. Fan, Z.Y. Su, J.B. Wu, Z.G. Xiao, P. Huang, L. Liu et al., Integrating continuous-stirred microwave pyrolysis with ex-situ catalytic upgrading for linear low-density polyethylene conversion: effects of parameter conditions. J. Anal. Appl. Pyrol. 157, 105213 (2021)
X.D. Jing, J.Q. Dong, H.L. Huang, Y.X. Deng, H. Wen, Z.H. Xu et al., Interaction between feedstocks, absorbers and catalysts in the microwave pyrolysis process of waste plastics. J. Clean. Prod. 291, 125857 (2021)
X.Y. Jie, W.S. Li, D. Slocombe, Y.G. Gao, I. Banerjee, S. Gonzalez-Cortes et al., Microwave-initiated catalytic deconstruction of plastic waste into hydrogen and high-value carbons. Nat. Catal. 3, 902–912 (2020)
Acknowledgements
The National Natural Science Foundation of China (Grant No.51961020) supported this work. The authors would like to thank Yunnan Province "Xingdian Talent Support Plan" industrial innovative talents (XDYC-CYCX-2022-0044).
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
Conflict of Interest
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Guangxiong, J., Bingguo, L., Guolin, L. et al. Research Progress on Gas Generation from Waste Plastics Through Pyrolysis. Korean J. Chem. Eng. (2024). https://doi.org/10.1007/s11814-024-00216-z
Received:
Revised:
Accepted:
Published:
DOI: https://doi.org/10.1007/s11814-024-00216-z