Skip to main content
SpringerLink
Log in

Tribological performance of Zr–O–N coating in marine environment fabricated by arc ion plating

  • Metals & corrosion
  • Published:
Journal of Materials Science Aims and scope Submit manuscript

Abstract

Zr–O–N coatings with varying oxygen contents were fabricated through arc ion plating, and their microstructure, mechanical properties and tribological behaviour in a seawater environment were evaluated. Zr–O–N composite coatings were fabricated by introducing oxygen elements during the deposition of ZrN coatings. The oxygen content of the coatings increased to 46.88 at% as the oxygen flow rate increased from 0 to 180 sccm. The coatings consisted of ZrN and ZrO2 phases. Grain size decreased from the micron to the nanometer scale when the oxygen flow rate exceeded 120 sccm. In scratch tests, the coatings prepared with a flow rate of 60 sccm exhibited the remarkable presence of debris and cracks, whereas only microcracks were observed in the coatings deposited under flow rates exceeding 120 sccm. Additionally, all coatings showed no signs of peeling even when subjected to a load of 100 N. The highest hardness value of 26.11 GPa was achieved by the composite coatings deposited under a flow rate of 60 sccm. However, hardness consistently decreased as the oxygen flow rate increased, reaching 17.68 GPa in the coatings deposited under a flow rate of 180 sccm. The tribological behaviour and failure mechanism of the coatings in a seawater environment were also analysed. The composite coatings deposited at 120 sccm exhibited the lowest friction coefficient of 0.19, whereas the those deposited at 180 sccm demonstrated the minimal wear rate of 5.65 × 10−8 mm3/(N m). When the coating with high oxygen content was rubbed in the seawater environment, the coating components underwent a tribochemical reaction with water to generate Zr–OH and O–OH, which exerted lubricating effects during friction and greatly reduced the friction coefficient and wear rate. The introduction of the appropriate amount of oxygen improved the tribological performance of the Zr–O–N coatings in marine environments effectively.

Graphical abstract

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
EUR 32.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or Ebook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10

Similar content being viewed by others

References

  1. Zhang L, Shao MH, Wang ZW, Zhang ZH, He YY, Yan JW, Lu JP, Qiu JX, Li Y (2022) Comparison of tribological properties of nitrided Ti–N modified layer and deposited TiN coatings on TA2 pure titanium. Tribol Int 174:107712. https://doi.org/10.1016/j.triboint.2022.107712

    Article  CAS  Google Scholar 

  2. Atar E, Kayali ES, Cimenog H (2006) Sliding wear behaviour of ZrN and (Zr, 12wt% Hf)N coatings. Tribol Int 39:297–302. https://doi.org/10.1016/j.triboint.2005.01.038

    Article  CAS  Google Scholar 

  3. Santecchia E, Hamouda AMS, Musharavati F, Zalnezhad E, Cabibbo M, Spigarelli S (2015) Wear resistance investigation of titanium nitride-based coatings. Ceram Int 41:10349–10379. https://doi.org/10.1016/j.ceramint.2015.04.152

    Article  CAS  Google Scholar 

  4. Johansen OA, Dontje JH, Zenner RLD (1987) Reactive arc vapor ion deposition of TiN, ZrN and HfN. Thin Solid Films 153:75–82. https://doi.org/10.1016/0040-6090(87)90171-4

    Article  CAS  Google Scholar 

  5. Pichon L, Girardeau T, Straboni A, Lignou F, Guérin P, Perrière J (1999) Zirconium nitrides deposited by dual ion beam sputtering: physical properties and growth modelling. Appl Surf Sci 150:115–124. https://doi.org/10.1016/S0169-4332(99)00233-0

    Article  CAS  Google Scholar 

  6. Singh A, Kumar N, Kuppusami P, Prasanthi TN, Chandramohan P, Dash S, Srinivasan MP, Mohandas E, Tyagi AK (2012) Tribological properties of sputter deposited ZrN coatings on titanium modified austenitic stainless steel. Wear 280–281:22–27. https://doi.org/10.1016/j.wear.2012.01.013

    Article  CAS  Google Scholar 

  7. Aissani L, Alhussein A, Abdelhak AYAD, Nouveau C, Zgheib E, Belgroune A, Zaabat M, Barille R (2021) Relationship between structure, surface topography and tribo-mechanical behavior of Ti–N thin films elaborated at different N2 flow rates. Thin Solid Films 724:38598. https://doi.org/10.1016/j.tsf.2021.138598

    Article  Google Scholar 

  8. Kumar A, Mulik RS (2024) Temperature-dependent morphological evaluation of in situ grown hard ZrN coating for enhanced mechanical, wetting and electrochemical properties. J Mater Eng Perform 33:3167–3187. https://doi.org/10.1007/s11665-023-08223-7

    Article  CAS  Google Scholar 

  9. González-Carmona JM, Triviño JD, Gómez-Ovalle Á, Ortega C, Alvarado-Orozco JM, Sánchez-Sthepa H, Avila A (2020) Wear mechanisms identification using Kelvin probe force microscopy in TiN, ZrN and TiN/ZrN hard ceramic multilayers coatings. Ceram Int 46:24592–24604. https://doi.org/10.1016/j.ceramint.2020.06.248

    Article  CAS  Google Scholar 

  10. Lin SS, Zhou KS, Dai MJ, Hu F, Shi Q, Hou HJ, Wei CB, Li FQ, Tong X (2015) Effects of surface roughness of substrate on properties of Ti/TiN/Zr/ZrN multilayer coatings. T Nonferr Metal Soc 25:451–456. https://doi.org/10.1016/S1003-6326(15)63623-8

    Article  CAS  Google Scholar 

  11. Brugnoni C, Lanza F, Macchi G, Müller R, Parnisari E, Stroosnijder MF, Vinhas J (1998) Evaluation of the wear resistance of ZrN coatings using thin layer activation. Surf Coat Technol 100–101:23–26. https://doi.org/10.1016/S0257-8972(97)00582-3

    Article  Google Scholar 

  12. Zambrano DF, Hernández-Bravo R, Ruden A, Espinosa-Arbelaez DG, González-Carmona JM, Mujica V (2023) Mechanical, tribological and electrochemical behavior of Zr-based ceramic thin films for dental implants. Ceram Int 49:2102–2114. https://doi.org/10.1016/j.ceramint.2022.09.176

    Article  CAS  Google Scholar 

  13. Kiahosseini SR, Afshar A, Larijani MM, Yousefpour M (2017) Structural and corrosion characterization of hydroxyapatite/zirconium nitride-coated AZ91 magnesium alloy by ion beam sputtering. Appl Surf Sci 401:172–180. https://doi.org/10.1016/j.apsusc.2017.01.022

    Article  CAS  Google Scholar 

  14. Chinsakolthanakorn S, Buranawong A, Chiyakun S, Limsuwan P (2013) Effects of titanium sputtering current on structure and morphology of TiZrN films prepared by reactive DC magnetron Co-sputtering. Mater Sci Appl 4:689–694. https://doi.org/10.4236/msa.2013.411086

    Article  CAS  Google Scholar 

  15. Aissani L, Fellah M, Belgroune A, Obrosov A, Samad MA, Alhussein A (2021) Effect of O2 flow rate on the structure, wettability and tribo-mechanical behaviour of Zr–O–N thin films. Surf Interfaces 26:101441. https://doi.org/10.1016/j.surfin.2021.101441

    Article  CAS  Google Scholar 

  16. Chauhan KV, Rawal SK (2014) A Review paper on tribological and mechanical Properties of ternary nitride based coatings. Procedia Technol 14:430–437. https://doi.org/10.1016/j.protcy.2014.08.055

    Article  Google Scholar 

  17. Leonov AA, Savostikov VM, Denisov VV et al (2023) Comparison of properties of the ZrN mononitride coating and (Zr + Ti–B–Si–Ni)N multicomponent coating obtained by vacuum-Arc plasma-assisted deposition. J Surf Investig 17(Suppl 1):S43–S50. https://doi.org/10.1134/S1027451023070315

    Article  CAS  Google Scholar 

  18. Yin M, Liang WP, Miao Q, Yu HY (2021) Effects of Ta content on the oxidation and high-temperature tribological behaviors of (Zr, Ta) N coating deposited by double-cathode glow plasma alloy. Ceram Int 47:34072–34085. https://doi.org/10.1016/j.ceramint.2021.08.317

    Article  CAS  Google Scholar 

  19. Kumarasubramanian R, Kumar DD, Preetham RMS, Reddy PBK (2021) Deposition and characterization Zr-Al-N coatings prepared by magnetron sputtering for tribological applications. Mater Today: Proc 44:3701–3706. https://doi.org/10.1016/j.matpr.2020.11.085

    Article  CAS  Google Scholar 

  20. Braic M, Balaceanu M, Vladescu A, Zoita CN, Braic V (2011) Study of (Zr, Ti)CN, (Zr, Hf)CN and (Zr, Nb)CN films prepared by reactive magnetron sputtering. Thin Solid Films 519:4092–4096. https://doi.org/10.1016/j.tsf.2011.01.375

    Article  CAS  Google Scholar 

  21. Choi H, Jang J, Zhang TF, Kim J, Park I, Kim KH (2014) Effect of Si addition on the microstructure, mechanical properties and tribological properties of Zr–Si–N nanocomposite coatings deposited by a hybrid coating system. Surf Coat Technol 259:707–713. https://doi.org/10.1016/j.surfcoat.2014.10.008

    Article  CAS  Google Scholar 

  22. Hsiao H, Huang J, Yu G (2016) Effect of oxygen on fracture toughness of Zr(N, O) hard coatings. Surf Coat Technol 304:330–339. https://doi.org/10.1016/j.surfcoat.2016.07.026

    Article  CAS  Google Scholar 

  23. Cunha L, Vaz F, Moura C (2006) Structural evolution in ZrNxOy thin films as a function of temperature. Surf Coat Technol 200:2917–2922. https://doi.org/10.1016/j.surfcoat.2004.09.030

    Article  CAS  Google Scholar 

  24. Ichou H, Arrousse N, Berdimurodov E et al (2024) Exploring the advancements in physical vapor deposition coating: a review. J Bio Tribo Corros 10:3. https://doi.org/10.1007/s40735-023-00806-0

    Article  Google Scholar 

  25. Kuznetsova TA, Lapitskaya VA, Chizhik SA (2018) Influence of the third element additives on the surface morphology of the wear-resistant ZrN coatings. IOP Conf Ser Mater Sci Eng 443:12–17. https://doi.org/10.1088/1757-899X/443/1/012017

    Article  Google Scholar 

  26. Lei ZF, Zhang QQ, Zhu XD (2018) Corrosion performance of ZrN/ZrO2 multilayer coatings deposited on 304 stainless steel using multi-arc ion plating. Appl Surf Sci 431:170–176. https://doi.org/10.1016/j.apsusc.2017.06.273

    Article  CAS  Google Scholar 

  27. Ding Z, Wen X, Qu R, Fu Y, Yao R, Lu J (2020) Robust lubricious and low corrosive imidazolium hexafluorophosphate lubricant on multi-arc ion plating Ag-Cu/Ti film under sliding electrical contact. Tribol Int 151:106451. https://doi.org/10.1016/j.triboint.2020.106451

    Article  CAS  Google Scholar 

  28. Vaz F, Carvalho P, Cunha L, Rebouta L, Moura C, Alves E, Ramos AR, Cavaleiro A, Goudeau Ph, Rivière JP (2004) Property change in ZrNxOy thin films: effect of the oxygen fraction and bias voltage. Thin Solid Films 469–470:11–17. https://doi.org/10.1016/j.tsf.2004.06.191

    Article  CAS  Google Scholar 

  29. Khan IA, Ikhlaq U, Farid A (2015) Role of nitrogen pressure on the structural and mechanical properties of ZrON composite films deposited by plasma focus device. J Fus Energ 34:1284–1296. https://doi.org/10.1007/s10894-015-9956-x

    Article  CAS  Google Scholar 

  30. Huang JH, Hu YY, Yu GP (2011) Structure evolution and mechanical properties of ZrNxOy thin film deposited on Si by magnetron sputtering. Surf Coat Technol 205:5093–5102. https://doi.org/10.1016/j.surfcoat.2011.05.015

    Article  CAS  Google Scholar 

  31. Dang B, Yang K, Tian T et al (2024) Mechanical, tribological, corrosion and tribocorrosion properties of ZrNxOy coatings on Ti–45Nb alloys by multi-arc ion plating. J Mater Sci 59:7060–7074. https://doi.org/10.1007/s10853-024-09575-8

    Article  CAS  Google Scholar 

  32. Huang JH, Zou SL, Xiao WW, Yang C, Tang DW, Yu HX, Zhang L, Zhang K (2021) Influences of arc current on microstructure of Cr coating for Zr-4 alloy prepared by multi-arc ion plating via EBSD. Mater Charact 178:111211. https://doi.org/10.1016/j.matchar.2021.111211

    Article  CAS  Google Scholar 

  33. Niu EW, Li L, Lv GH, Chen H, Feng WR, Fan SH, Yang SZ, Yang XZ (2007) Influence of substrate bias on the structure and properties of ZrN films deposited by cathodic vacuum arc. Mater Sci Eng A 460–461:135–139. https://doi.org/10.1016/j.msea.2007.02.085

    Article  CAS  Google Scholar 

  34. Carvalho P, Vaz F, Rebouta L (2005) Structural, electrical, optical and mechanical characterization of decorative ZrOxNy thin films. J Appl Phys 98:195. https://doi.org/10.1063/1.1990261

    Article  CAS  Google Scholar 

  35. Huang JH, Ho CH, Yu GP (2007) Effect of nitrogen flow rate on the structure and mechanical properties of ZrN thin films on Si(100) and stainless steel substrates. Mater Chem Phys 102:31–38. https://doi.org/10.1016/j.matchemphys.2006.10.007

    Article  CAS  Google Scholar 

  36. Chou WJ, Yu GP, Huang JH (2001) Deposition of TiN thin films on Si(100) by HCD ion plating. Surf Coat Technol 140:206–214. https://doi.org/10.1016/S0257-8972(01)01120-3

    Article  CAS  Google Scholar 

  37. Huang JH, Lin TC, Yu GP (2011) Phase transition and mechanical properties of ZrNxOy thin films on AISI 304 stainless steel. Surf Coat Technol 206:107–116. https://doi.org/10.1016/j.surfcoat.2011.06.051

    Article  CAS  Google Scholar 

  38. He YJ, Winnubst AJA, Schipper DJ, Burggraaf AJ, Verweij H (1997) Effects of a second phase on the tribological properties of Al2O3 and ZrO2 ceramics. Wear 210:178–187. https://doi.org/10.1016/S0043-1648(96)07515-1

    Article  CAS  Google Scholar 

  39. Zhou Z, Rainforth WM, Luo Q, Hovsepian PEh, Ojeda JJ, Romero-Gonzalez ME (2010) Wear and friction of TiAlN/VN coatings against Al2O3 in air at room and elevated temperatures. Acta Mater 58:2912–2925. https://doi.org/10.1016/j.actamat.2010.01.020

    Article  CAS  Google Scholar 

Download references

Acknowledgements

This work was financially supported by the Key R & D Programs in Zhejiang Province (Grant No. 2020C03102), the Major Project of Science and Technology Innovation 2025 in Ningbo City (Grant No. 2022Z052), The China Postdoctoral Science Foundation (Grant No. 2023M733596).

Funding

Key Research and Development Program of Zhejiang Province, Grant No. 2020C03102, Yongxin Wang, Science and Technology Innovation 2025 Major Project of Ningbo, Grant No. 2022Z052, Yongxin Wang, China Postdoctoral Science Foundation, 2023M733596, Chongqing Di

Author information

Authors and Affiliations

  1. School of Materials Science and Engineering, Shanghai University, Shanghai, 200444, People’s Republic of China

    Yuqing Peng & Linheng Yang

  2. Key Laboratory of Advanced Marine Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo, 315201, People’s Republic of China

    Linheng Yang, Yongxin Wang & Chongqing Di

  3. Ningbo Zhongyi Hydraulic Motor Co., Ltd, Ningbo, 315200, People’s Republic of China

    Xiaojiang Lu

  4. University of Chinese Academy of Sciences, Beijing, 100049, People’s Republic of China

    Yongxin Wang

Authors
  1. Yuqing Peng
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Linheng Yang
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Yongxin Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Chongqing Di
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Xiaojiang Lu
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

Yuqing Peng contributed to the modification; Linheng Yang was involved in the writing—original draft preparation; Yongxin Wang contributed to the modification; Chongqing Di assisted in the article review and edit; Xiaojiang Lu was involved in the picture curation and modification.

Corresponding authors

Correspondence to Yongxin Wang or Chongqing Di.

Ethics declarations

Conflict of interest

The authors declare that they have no conflict of interest or competing interests.

Ethical approval

Not applicable.

Additional information

Handling Editor: Maude Jimenez.

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Peng, Y., Yang, L., Wang, Y. et al. Tribological performance of Zr–O–N coating in marine environment fabricated by arc ion plating. J Mater Sci (2024). https://doi.org/10.1007/s10853-024-09930-9

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s10853-024-09930-9

Search

Navigation