All Questions
Tagged with measurement sensor
68
questions
0
votes
1
answer
105
views
How do I calculate the minimum deflection I can sense with a strain gauge, like the BF350-3AA?
I have a strain gauge (the BF350-3AA), and I will be connecting it to an HX711-based amplifier sensor.
From its low-quality datasheet, I've pulled out the following figures:
Nominal Resistance: 350 ...
1
vote
1
answer
352
views
How do I read a load cell just with this data?
I have a load cell (capability = 23 kg or 50 lb.) Its output is 2 mV/V. I have read that that means 2 mV per each excitation volt.
The power connection of this load cell is +15V-GND, so 0.002 * 15 = ...
1
vote
1
answer
226
views
Need help with validation of the design of a capacitance sensor array for soil moisture measurement
Product Description
The device is a soil moisture sensing and analysis device that uses capacitance sensing technology to help manage soil moisture in your garden. One probe set at the bottom of the ...
1
vote
0
answers
50
views
Contact measurement
I have a mechanical assembly that is to be mated to another surface. To ensure that my assembly is correctly mounted before installation, I have a test piece I insert into it. When everything is OK ...
-1
votes
1
answer
217
views
Accuracy Class and Full Scale
I am using this formula to calculate the class of an instrument:
\$\text{Accuracy Class} = \frac{\max{\text{(Absolute Error in Range of Measurement)}}}{\text{Full Scale Value}}\$
The question is, FSV ...
2
votes
1
answer
186
views
How to make an accurate strain gauge conditioner
I need to measure tensile strains between 0 and 0.01%, with an accuracy between 1 to 10% within that range.
It seems like all systems that read strain gauges rely on a Wheatstone bridge to amplify ...
0
votes
3
answers
82
views
Signals transmission
If I have more than one sensor that provides a digital output (1 or 0 only,) and I only have one pair of wires connected from all the sensors to a specific point (assume the sensors are at point A and ...
2
votes
0
answers
204
views
Electrochemical Gas Sensor Potentiostat Circuit
I guess this is more of a review request than a specific question, but I was wondering if anyone has any experience with electrochemical sensors and the required circuits for gaining accurate ...
2
votes
3
answers
579
views
Resistance bridge for low-resistance sensor
I have a fuel tank sensor that reports the remaining fuel with a resistance between 10 ohms (empty) and 180 ohms (full). I want to read this value using the Analog In of an Arduino (or ADS1115, not a ...
0
votes
2
answers
268
views
Is there a way to measure ripples in water with some kind of sensor?
Imagine you have a water tank on the top of a truck (like firefighters have.)Is there a way to measure how much the water ripples with some sensor?
I know sensors that just tell you if there is water ...
0
votes
2
answers
104
views
Does shunt calibration of a sensor also correct for zero error?
In the datasheet for a load cell (shown below), it says that shunt calibration data is given, also they have mentioned the zero balance. Does the shunt calibration consider zero balance? Meaning, do I ...
0
votes
1
answer
48
views
How wide is IR-led light from VCNL4040?
I have an issue to solve. I'm going to measure an object that looks like this.
My question is if the sensor VCNL4040 have a very wide spread light or very "laser-like" light that ...
13
votes
4
answers
3k
views
Why does it take time for electronic scale to measure?
If I am standing on a digital scale or measuring the weight of my luggage,
the display doesn't show the weight immediately - it takes a few fractions of a second.
Why is that and can you overcome it ...
2
votes
0
answers
303
views
Does creep always occur with load cells, or is there an optimum weight capacity?
I want to make a scale which I will place under a wood stove (downdraft gasifier) to measure the amount of wood that goes into the wood stove. The amount of wood which is being measured will be ...
0
votes
0
answers
41
views
Current Sensing IC (MAX9929F) Query
I am using a MAX9929F Current sensing IC and I have a question to someone to may have used it before, or may have some experience with these types of circuits.
The circuit I built around the IC is the ...