All Questions
Tagged with measurement impedance
31
questions
1
vote
1
answer
96
views
Measuring impedance on VNA
Question:
I would like to measure the impedance and phase of an electric piezo tranducer with a resonant frequency of approximately 1MHz - a graph of impedance in Ohms as a function of frequency.
...
0
votes
1
answer
152
views
Source impedance influence on DC/DC converter input impedance measurement
simulate this circuit – Schematic created using CircuitLab
I have been tasked to verify the input impedance of a medium powered DC/DC converter (<1kW), and no experienced colleagues to ...
2
votes
3
answers
179
views
Measuring variable impedance
I was wondering how to design a measurement system that's able to correctly measure a load impedance that can vary over time and can possibly have very low as well as very high values (see figure ...
1
vote
0
answers
101
views
How do I measure impedance at high power?
I need to measure the impedance of a passive device at its operating power, about 100-watts, and its operating frequency, from 0.1-MHz to 10-MHz. The venerable "operating impedance bridge" ...
1
vote
0
answers
85
views
How do you "calibrate" (?) a matching network to re-optimize an S11 match based on physical measurements from a VNA?
We made EDA simulations to match an LNA input and had good results on the simulation (including EM simulation!) --- but when we built the board in real life the S11 match went from -30dB to -7dB. Ouch....
1
vote
1
answer
138
views
How to measure output impedance of this circuit?
I have the following circuit with an operational frequency range of 100 - 10kHz, always square waves.
How do I measure the output impedance? I have access to an LCR meter (BK Precision 891.) Do I ...
1
vote
4
answers
172
views
Experimental material impedance measurement
Imagine we have a square-shaped conductive material to which we connect 3 electrodes E1, E2, and E3. Suppose we assume for this material a 'pi' two-port network model with impedances Za, Zb, and Zc (...
0
votes
2
answers
192
views
Two-port network parameter measurement using an LCR meter
I was wondering if it's possible to find the admittance parameters of a pi two-port network experimentally using an LCR meter.
For the network shown below, we have
$$
\begin{bmatrix}
I1\\
I2
\end{...
-1
votes
6
answers
831
views
Why is it not possible to measure PCB trace characteristic impedance using a multimeter?
I was looking into StackExchange posts for PCB trace impedance measurement.
How to measure trace impedance?
This posts clearly explains what the methods to be used for trace impedance measurement are.
...
3
votes
3
answers
429
views
How should I probe when measuring output impedance? Why do I get inconsistent readings?
I am trying to measure the output impedance of a commercial headphone amplifier, but the results seem to change depending on how I probe it. When I plug a 1m cable into the device and the other end ...
0
votes
1
answer
106
views
Vector Network Analyzers: Bode100 vs Keysight P5000A
I have been using Bode 100 machine earlier to measure Impedance and Phase of my piezoelectric transducer.
The frequency range i work in is from 10kHz to 2.5MHz.
I was just comparing this Bode100 with ...
1
vote
3
answers
609
views
What is the best way to measure current and voltage through a diode
I am reading the book Learning the art of electronics and on a part about diodes, the author pointed out that in characterizing a diode(I, V relation ) there is an unavoidable error due to the ammeter ...
0
votes
1
answer
85
views
Will multiplexing impedance measurements from the AD5933 act as a series resisitance?
Image of block diagram of the AD5933 at: https://www.researchgate.net/profile/Douglas_Dutra/publication/292976112/figure/fig1/AS:520210098917376@1501039160818/AD5933-Functional-Block-Diagram-10.png
I ...
1
vote
2
answers
1k
views
RLC equivalent model and Impedance Smith Chart
I have done some impedance measurements on an unknown 1 port device. I have measured its impedance at different frequencies (from 10 MHz to 600 MHz) and I have seen it on the normalized (on 50 Ohm) ...
1
vote
2
answers
1k
views
Agilent 4294A Impedance Analyzer: "Bridge Unbalanced" during calibration
I am having problems calibrating my test fixture for the Agilent 4294A Impedance Analyzer. The open measurement always works, but with the short measurement I always get the error message "Bridge ...